不合格品

Error-proof your control of the nonconforming product process so that nobody has to assume anything.

对不合格品进行防错控制不给人留下可乘之机。

Meanwhile, locate all unaccepted products, note down the number of defectives and note down those illness.

同时追溯所有涉及到的不良品，注明受影响的不良数，并在备注中注明不良纠正情况，如不能正常使用，则根据&不合格品控制程序&进行处理。

Meanwhile, locate all unaccepted products, note the number of defectives and note those illness that demand attention.

同时追溯所有涉及到的不良品，注明受影响的不良数，并在备注中注明不良纠正情况，如不能正常使用，则根据&不合格品控制程序&进行处理。

In fact, situation with a zero LCL is not uncommon. In this article we propose the g-type chart with asymmetric control limits. It is found that with the nonzero LCL, the power to detect rate increase hasmuch improved and the power to detect rate is nearly fixed, and the in-control average run length is the almost the same as the symmetric control chart.

为了解决检测p增加的问题，我们提出了非对称几何控制图的思想，它解决了虚报率增加和检测p增加之间的矛盾，在保持虚报率与对称几何控制图几乎相等的前提下，大大提高了几何控制图在检测不合格品率增加时的灵敏性和有效性，本文中给出了在不同的？

The control chart based on the geometric distribution(g-type chart) has shown to be competitive with p or np chart for monitoring the proportion especially for application in high quality manufacturing environments. However when the cases with LCL=0 occur, plotting values beneath the LCL is impossible given the non-negative nature of units, such type of lower control limits no ability to detect rate increase.

但是由于几何控制图的自然下限的问题，在其使用过程中若控制下限LCL＜0，则取其自然下限为0，这使得几何控制图在此情况下对于检测不合格品率p的增加是几乎不起任何作用，而此问题也是实际中我们最需要检测并作判断的问题。

Originally, the golf ball was a feather-stuffed and leather-covered one seamed with thread. The materials and process of the feathery ball involved such a complicated handcraft and a low level of stanardization that many products failed to meet the lowest standard.

最初的高尔夫球是用羽毛做芯，用皮革做外壳，缝制而成，这样的原料和加工方法不仅制作工艺难度大，而且标准化程度低，容易出现不合格品。

For question two,based on question one,the objective functions has been establis hed,and the optimum tactics of the best designed interval of check and thd repla cement of cutting tools has been obtained considering the average loss brought a bout by unqualified.products at the interval of check and the average loss of ma chine stop for being misregarded as existing breakdown.

针对问题二，在问题一的基础上，利用概率知识调整了检查间隔中的不合格品数带来的平均损失，同时加上了因工序正常而误认为有故障停机产生的平均损失，然后建立起目标函数，得到工序设计效益最好的检查间隔和刀具更换策略。

Chapter two studies the relationship between the PCIs and the nonconforming rate base on the traditional quality management.

第二章基于传统的质量管理观，研究过程能力指数与产品不合格品率之间的关系；建立了过程能力指数与过程利润的计量模型。

The main products are: 1, disposable nasal oxygen tube, connecting tube 2, the use of disposable skin knife 3, the use of disposable endotracheal intubation 4, the use of disposable suction device 5, analgesic pumps 6, all kinds of disposable Medical Product plastic fittings (tube, spatula, amniotic fluid hook, hemostatic forceps, medical÷×, probe, explore mirror, umbilical cord folders, folder catheter, all kinds of Medical Products joints, drainage bag fittings, etc.) 7, a variety of injection molding plastic products production of "Quality First, Customer Satisfaction" for business purposes, drawn up a strict management system, standardized database from raw material to finished product into a set of testing protocols, production grasp the key processes, technology standards and insist requirements, and resolutely put an end to the inflow of substandard goods procedures and to develop the workshop director is responsible for the quality of accountability, to achieve Total Quality Management, so that product quality has been ensured; inspectors at the same time continually improve operational standards and quality, meticulous preparation the inspection work to ensure that qualified factory Products; and perfect after-sale service and feedback management system, continuously enhance customer satisfaction, quality service to customers.

主要产品有：1、一次性使用鼻氧管、连接管 2、一次性使用备皮刀3、一次性使用气管插管 4、一次性使用吸痰器5、镇痛泵 6、各种一次性医用产品塑料配件（试管、压舌板、羊水钩、止血钳、医用镊子、探针、探镜、脐带夹、导管夹、各种医用产品接头、引流袋配件等）7、各种注塑塑胶产品生产等本公司以&质量第一，顾客满意&为企业宗旨，制定了严格的管理制度，规范了从原材料进库到成品出厂的一整套检验规程，生产中抓好关键工序，坚持工艺标准和要求，坚决杜绝不合格品流入下道工序，并制定车间主任负责的质量责任制，做到全员质量管理，使产品质量得到了保证；同时不断提高检验人员的业务水平和素质，一丝不苟作好各项检验工作，确保产品合格出厂；并完善售后服务和信息反馈管理制度，不断增强顾客的满意度，以优质产品服务广大用户。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了