下模

The lower die holder of machines be designed to meet with customer's needs. Please contact us for more information.

铆钉机的机台下之模座可依据客户的需求特别设计，请与我们联络以取得更详细的资料。

Based on finite element analysis of the die spotting machine frame,the real case of stress distribution and deformation is simulated,by which the biggest deformation and stress location are identified.

通过对合模机机架进行有限元分析，模拟了真实情况下机架的应力分布和位移变形情况，得到了位置变形最大和应力值最大的位置。

The CAD modules for sand casting mold on shrinkage allowance and pattern draft have been developed and can be run in a 3D environment. It uses the programming tool of Visual C++ and the secondary development tool ObjectARX.

开发出了可以运行于AutoCAD三维绘图环境下的砂型铸造模具CAD系统的收缩量和拔模斜度模块，开发工具为Visual C++。net 2002的编程工具和AutoCAD的二次开发工具ObjectARX。

The CAD modules for sand casting mold on shrinkage allowance and pattern draft have been developed and can be nm in a 3D environment. It uses the programming tool of Visual C++ and the secondary development tool ObjectARX.

开发出了可以运行于AutoCAD三维绘图环境下的砂型铸造模具CAD系统的收缩量和拔模斜度模块，开发工具为Visual C++。net2002的编程工具和AutoCAD的二次开发工具ObjectuARX。

The paper puts the drainage modulus theory system of short-term stopping storage theory calculation in waterlogging region based on the condition of design storm rainfall and design flood.

本文提出了基于设计暴雨、设计洪水条件下，应用短期停蓄法原理计算涝区排水模数理论体系。

Analysis of the performance of magnesium alloy AZ31, the existence of room temperature can not be the issue of drawing, through a detailed analysis of parts and access to relevant technical information, design process in deep drawing dies and parts for heating the drawing die, so it is easy to resolve these issues.

分析镁合金AZ31的性能，存在常温下不可拉深的问题，通过对零件进行详尽的分析和查阅相关技术资料，设计了在拉深过程中对模具和零件进行加热的拉深模，这样就很容易的解决了上述问题。

The influence of the eccentricity mass moment, position of mass center and the bearing stiffness to the vibration characteristics of the rotor system is discussed in detail; 3. To verify the exactness of FEM and learn the principle of vibration of dredge pump further, The orbit of the rotor shaft of the pump in the dredger is measured, the measurement results show: the repeat of the orbit of the rotor shaft is very bad when dredge pump is in the dredging mud condition.

模态分析确定了泥泵的振动特性；谐响应分析确定了泥泵转子轴在偏心力的作用下轴截面处的最大响应位移；研究了转子轴的质心位置、轴承刚度和质量偏心矩对转子轴振动特性的影响； 3、采用轴心轨迹法，实船测量了泥泵轴工作时振动响应值。

A kiln for drying hops or malt or drying and curing tobacco.

砖块在太阳下或窑里烘烤变硬的模制长方形黏土砖，用作建房和铺路的材料

Based on simulation principles of two-phase flow,a test rig has been set up for studying multi-phase flow,during flue gas desulfurization ,in topping alkaline atomizers.

根据两相流相似模化原理建立了前置碱雾发生器烟气脱硫颗粒图像测速技术多相流动实验台，运用颗粒图像测速技术对前置碱雾发生器内气液固三相流动进行测量，得到不同工况条件下喷雾射流与固体颗粒的流动结构和流场信息。

The peak responses at different wind azimuths are calculated with the CQC method and the SRSS method, and the effects of modal coupling are checked.

采用完全二次型组合法和平方总和开方法计算了不同风向角下的峰值响应，说明了模态耦合的影响。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。