下模

In some cases, instead of a cast, a splint made a plastic or metal will be secured over the area to restrict movement.

在一些情况下也可以不用石膏模，而是用由塑料或金属制成的夹板来保护受伤区域而限制它的运动。

Unigen's core competency is the design and manufacture of precise and complex standard and custom module products.

Unigen的核心竞争力是能为客户设计并生产复杂的标准下最精确的模组产品。

By means of stereotaxis instrument, 1×105 BMSCs (2 μL) of passage 3 stained with Hochest33324 for 24 hours were transplanted into the left hippocampus at 24 hours, 72 hours and 7 day after induction of HIBD in the corresponding groups.

在脑立体定位仪下，24 h，72 h，7 d细胞移植组分别于造模后对应时间点，将体外培养3~5代且经Hochest33324标记24 h的鼠骨髓基质细胞2 μL脑内移植于左侧海马，约105个细胞。

The paper has investigated the robust control and simulation of systems with stochastic perturbation in internal model control structure.

在内模控制结构下对一类随机摄动系统的鲁棒控制及其仿真研究作了探讨。

Based on limiting the tensile strain at the bottom of the asphalt layer and the vertical compressive strain at the top of the subgrade, the suitability of layer thickness is checked by two criteria. One is controlling the maximum surface deflection under the design load, and the other is controlling the modulus ratio between adjacent unbound aggregate base and subbase layer.

该方法基于限制沥青层底的拉应变和路基顶面的压应变，采用两个准则来校核所设计的沥青层厚度的适宜性：一是控制设计荷载作用下的最大路表弯沉；二是控制相邻两个无结合料处治的集料层的模量比。

We compose a neural network in which the input signals are the frame substructure natural frequencies and mode shapes, and output signals are the submatrix scaling factor.

框架子结构在动载作用下的自振频率和模态作为网络的输入，子矩阵参与系数作为网络的输出，用Levenberg一Marquardi算法训练网络。

FEM model of coupled acoustic-structure is set up, modal superpose method is used to deduce sensitivity of response acoustic pressure level to structure design variable.

基于结构-声场耦合系统有限元模型，用有限元模态叠加法推导了系统在动力载荷作用下响应声压级对结构设计变量的灵敏度。

When the ratio of compressive modulus of superstratum and substratum is less than 3,academic diffused angles of natural subgrade with soft substratum under pressure in this paper are investigated.

对上下层土压缩模量比小于3的软弱下卧层的压力扩散角进行了研究，得出了扩散角理论值，可供相应工程参考。

A molded plastic bottle (10) has a base (24) having an outside surface rotationally symmetric about a longitudinal axis of the bottle including a convex heel (26) and a central concavity (28) separated by a standing ring (30) supporting the bottle on an underlying surface.

一种模制的塑料瓶(10)，具有一个带有绕瓶子的纵轴转动对称的外表面的底座(24)，该底座包括凸出的跟部(26)和中心凹面(28)，它们用将瓶子支撑在任何下垫面上的立环(30)互相分开。

A Hamiltonian system was constructed for the fundamental problem of the dynamic buckling ,thereby problems of critical loads and buckling modes were reduced to determinations of eigenvalues and eigensolutions in a symplectic space and a symplectic method was proposed.

针对有内压或外压的弹性圆柱壳在轴向冲击载荷耦合作用下的动态屈曲问题，构造哈密顿体系，在辛空间中将临界载荷和动态屈曲模态归结为辛本征值和本征解问题，从而形成一种辛方法。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。