下模

Furthermore, we show that the constant modulus cost function with non-canonical constraint is strictly convex under some conditions.

然后证明具有非标准约束的常数模准则在适当条件下是严格凸的。

Based on the modal superposition method and the exact solution of beam nature vibration, the motion equations of the simply supported and continuo...

基于模态叠加法和梁固有振动的精确解，建立了移动荷载作用下简支梁和连续梁的运动方程；利用样条最小二乘法逼近桥梁应变响应，由样条数值微分求得响应导数；再通过Tikhonov正则化方法结合奇异值分解技术得到了荷载识别的正则解。

From simulation, the 1st modal frequency and modal deformation could be achieved under different fixed ways.

然后结合模态实验的方法进行了不同边界条件下的动态测试分析。

By analyzing the process of bending cross beam , this article elaborates different factors that affect the resilience under different conditions, from which we find out solution for resilience.

通过弯曲横梁的工艺分析，在不同的条件下，影响回弹的因素也不同，从中找出解决回弹的方法，用一套补偿回弹量的弯曲模来完成该件的制做。

A frequency domain poly reference modal identification method under operational conditions was presented on the basis of the cross correlation function of measured responses to solve the only output problem.

针对工程实际情况，从实测响应间的互相关函数入手，推导出适用于工作状态下的频域多参考点模态识别法，然后采用一飞机模型对该方法进行了试验验证。

Based on the method of modal analysis, it can be concluded that ANSYS has directive values to dynamic simulation and structural optimization of crossbeam, and the research has laid a foundation for the harmonic response analysis of the next step.

通过模态分析法，可以看出ANSYS对横梁的动态仿真和结构优化有一定的指导意义，也为下一步的谐响应分析提供依据。

In Chapter 6, the self-induced geometric phase of laser field when possessing cyclic attractors and the complex Berry's phase under the adiabatic evolution of backscattering coefficients when not, including the case of having noises, are considered in a two-mode ring laser with backscattering.

在第6章中讨论了具有后向散射的双模环形激光具有周期吸引子时的自诱导几何相和不具有周期吸引子时在后向散射系数绝热演化下的复Berry相。

In plastic step sucking back is very important too. Sucking back include front sucking back and back sucking back It setting sucking back to prevent flow and line. It sets sucking back speed and pressure within 20-50% and distance within 2-5cm. TOO long distance make cyclinder reserve air and cause bubbleat next molding.

熔胶过程还有一个比较重要的环节，那就是松退，松退分前松退和后松退，其作用一般是为了防止流涎和抽丝，设定值速度和压力都在20%-50%间，设定的行程一般在2-5cm间，太长的行程可能会使料筒里面贮存空气，导致下一模出现不期望的气泡。

In plastic step sucking back is very important too. Sucking back include front sucking back and back sucking back It setting sucking back to prevent flow and line. It sets sucking back speed and pressure within 20-50% and distance within 2-5cm. TOO long distance make cyclinder reserve air and causebubble at next molding.

熔胶过程还有一个比较重要的环节，那就是松退，松退分前松退和后松退，其作用一般是为了防止流涎和抽丝，设定值速度和压力都在20%-50%间，设定的行程一般在2-5cm间，太长的行程可能会使料筒里面贮存空气，导致下一模出现不期望的气泡。

In plastic step sucking back is very important too. Sucking back include front sucking back and back sucking back It setting sucking back to prevent flow and line. It sets sucking back speed and pressure within 20-50% and distance within 2-5cm. TOO long distance make cyclinder reserve air and cause bubble at next molding.

熔胶过程还有一个比较重要的环节，那就是松退，松退分前松退和后松退，其作用一般是为了防止流涎和抽丝，设定值速度和压力都在20%-50%间，设定的行程一般在2-5cm间，太长的行程可能会使料筒里面贮存空气，导致下一模出现不期望的气泡。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。