下模

According to the change regularity of deformation modulus, combining with the rock mass structure characteristic of region studied, using interpolation method, the deformation modulus of rock mass in 36# adit can be deduced. The average vertical deformation modulus of rock mass during 0-70 zone is 39Gpa, and the horizontal deformation modulus of rock mass is 51. 3GPa in nature stress state and 50.8GPa in engineering load state. The average vertical deformation modulus of rock mass during 70-140 zone is 32. 2Gpa, and the horizontal deformation modulus of rock mass is 41GPa in nature stress state and 42. 6GPa in engineering load state. It will be a good reference of engineering design and evaluation.

9根据节理岩体变形模量变化规律，结合研究区岩体的结构特点，采用插值的方法对36号平硐岩体进行变形模量的推测，得到0-70段岩体的平均铅直向的变形模量为39GPa，水平向的变形模量：天然应力状态下为51.3GPa，工程荷载作用下为50.8GPa；70-140段岩体的平均铅直向的变形模量为32.2GPa，平向的变形模量：天然应力状态下为41GPa，工程荷载作用下为42.6GPa，这为工程设计、评程设计、评价等提供了必要的参考。

Figure 3 shows the frequency response function determined by the help of a modal analysis based on the impact hammer method.

图3显示频率响应函数确定的帮助下模态分析的基础上，冲击锤的方法。

The temperature time curve of the heated die cavity and the relation between temperature and time under different initiatory temperature were determined .

测定模膛加热的温度-时间曲线及不同起始温度下模膛温度与时间的关系。

In order to optimize the technology of press and lower the production cost,a two-stage floating elastic pressing structure at the anvil swage of the second punching die was adopted.

为优化冲压工艺，降低生产成本，第2副冲模采用了下模部分二级浮动弹压的结构，成功实现局部胀拉和翻边工艺以及压凸、弯曲、整形多道工序一次成形。

It is regular to put the mould, have the activity type of the mould, for inlaying Two sections of temperature control.

下模固定，上型活动式，对于镶入物品有良好的定位性，且具有成品顶出装置。

Identify the components of the lower die shoe.

识别下模座的零件

This new technology inserts UHF and HF inlays under die-cut blank or pre-printed labels and validates the finished product.

这项新技术插入UHF和HF标签下模切空白或预印标签和验证成品。

Clean the machine including the surface, base, slip board, groove, pressed board and oriented pole in the fixed time.

定期清洁机台表面、底板及下模滑板、沟槽、上模内压板及保险杆（注：必须关闭电源并恢复常温）。

Regarding a tractive elevator as example, according to the drawing and measurement of its parts, and computing with Ansys, its dynamic parameters are obtained, which are used in analysis of horizontal direction vibration with Matlab.

第五章，在电梯数值计算模块的基础上，开发了电梯动态特性仿真平台，并用来进行电梯各种工况下模态分析、谐响应分析、瞬态动力学响应分析。

In addition, the modal analysis is made using FEA method in three working states: fixing the reinforced panel upon the slip table, the slip table and vibration fixture as a vibrating system, and considering the mass of satellite.

通过有限元方法分析了安装加强台面后对水平滑台、水平滑台与振动花盆组成的振动工装系统、考虑卫星质量影响的振动工装系统等三种工况下模态振型的变化，说明抗弯模量有明显提高。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。