下模

Compiled procedure based on the overall geometric dimensions and load parameter of DXZ32/900 downward-borne self-propelled mobile framework template and concrete girder with the secondary development tool APDL of ANSYS, achieved the aim of generating finite element model and imposing load of the template and concrete girder automatically,finally,calculated the counterforce of the outer-mould and rod.

利用ANSYS二次开发工具APDL，依据DXZ32/900下承自行式移动模架模板及混凝土梁整体的几何尺寸和荷载参数编写程序，实现了模板和混凝土梁有限元模型的自动生成、荷载的自动施加，并得出外模及撑杆的支反力。

The results indicate that the difference between the top and the bottom kerfs width of the die-board along eight directions is not sensitive to linear polarization with altering laser power and cutting speed, while the kerf width difference of steel is on the contrary.

试验结果表明，改变激光功率和切割速度对模切板进行切割，上、下切缝沿不同方向之间的宽度相差不大，即偏振性对高吸收率非金属材料模切板的切缝影响不大，但是对金属材料影响很大。

This paper presents the Proteus software under a micro-controller board simulation method, and gives a digital-to-analog converter, analog-to-digital conversion、ISP programming、numeral clock 、real-time digital clock ﹑ Lantern experimental keyboard ﹑lattice LED ﹑ Relay, voice and other tenets of the hardware modules and software flow chart.

本文介绍了在Proteus软件下实现了一套单片机实验板的仿真方法，并给出了数模转换、模数转换﹑ISP编程﹑数字钟﹑实时时钟、键盘﹑彩灯实验﹑点阵LED显示屏﹑继电器、语音等模块的硬件原理及软件流程图。

This paper presents the Proteus software under a micro-controller board simulation method, and gives a digital-to-analog converter, analog-to-digital conversion、ISP programming、numeral clock 、real-time digital clock ﹑ Lantern experimental keyboard ﹑lattice LED ﹑ Relay, voice and other tenets of the hardware modules and software flow chart.

论文编号：JD607 包括开题报告，任务书，外文翻译，论文字数：10522，页数：46本文介绍了在Proteus软件下实现了一套单片机实验板的仿真方法，并给出了数模转换、模数转换﹑ISP编程﹑数字钟﹑实时时钟、键盘﹑彩灯实验﹑点阵LED显示屏﹑继电器、语音等模块的硬件原理及软件流程图。

The stable lobe graph for high speed milling of 2A12 aluminum alloy thin-walled workpieces was obtained by utilizing modal parameters and force coefficients,which were acquired respectively by milling tests and modal analysis tests on Mikron high speed...

针对2A12铝合金薄壁结构零件，利用M ikron高速加工中心和相关仪器，通过铣削力实验和模态实验，分别测得特定刀具和工件系统的动态铣削力系数和模态参数，从而绘制出高速铣削薄壁零件的稳定性叶瓣图，得到了不同径向切深条件下的极限轴向切深，并通过试验进行了验证。

The slip form spreading machine was used to construct the Taian-Qufu highway concrete pavement, and the machine can continuously complete the construction procedures (including spreading, vibrating, strickling, forming, float finishing and dowel bar setting) without fixed form, so this technology is advanced, and is worth extending.

泰曲路改造工程三合同段的混凝土路面采用滑模摊铺机进行施工，滑模摊铺机在不用固定模板的情况下可以连续完成摊铺、振动、刮平、成形、抹光以及打设传力杆等工序，工艺先进，具有一定的推广价值。

Methods CT water phantom was scanned using the regular condition of seaning first, then changed one of seaning conditions （ thick slice, exposure capacity, reconstruction of function, kV, FOV and CT- scanner） to scan the water phantom again.

通过固定扫描条件对机器自带水模进行扫描，然后在其它条件不变的情况下，改变其中1个扫描条件（层厚、曝光量、重建函数、仟伏、FOV、机器）再对水模各扫描1次，测量CT图像一定兴趣区的CT值与固定扫描条件的图像相对应ROI的CT值进行比较。

For the first time, SPAMP technique applied on the locomotive and passenger vehicles is proposed by using both the theoretical modal parameter analysis and the operational modal parameter identification techniques.

本文在铁路客车实测试验的基础上，采用试验测试和样机分析相结合的方法综合研究铁路客车动力学问题，提出适合铁路客车动态特性研究的环境激励下的模态参数辨识方法，建立铁路客车运行特性和运行模态参数的关系，探索这些理论和方法在铁路客车的正确应用。

By establishing the large scale plate cutting center in a steelworks, the steelworks, plate cutting center , and users are related using the computer network.

通过在钢铁企业建立大现模金属材料下料中心，利用&计算机网络&将钢铁厂、金属材料下料中心及众多用户联系起来，使得钢厂的排产、金属材料下料中心的套料加工及用户产品的下料有序结合。

Due to different properties of the signal and noise in wave-let coefficient modulus under different scale of wavelet transformation, we can extract the edge characteristic through detecting the local maximum of the wavelet transformation coefficient modulus.

基于信号与噪声在不同尺度下小波系数模的变化特征，可以通过检测小波变换系数模局部极大值来提取图像的边缘特征。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。