下压

The results show that a surface layer of stable cobalt borides of CoB, CoW2 B2 and CoW3B3 formed at 950 ℃ can effectively reduce tKey words: diamond films; cemented carbide; boronizing pretreatment; adhesion

结果表明，基体经硼化预处理后表面形成CoB、CoW2B2、CoW3B3相；当沉积温度为750～800℃，碳源浓度为3.3%时，薄膜表面形貌和生长织构随着沉积气压改变有明显的变化；硼化预处理后所得样品在1500N载荷下压痕表现出良好的附着性能，较二步法预处理更加有效地改善了膜-基附着性能。

It comprehensive describes the attack number and scored rate of active and passive, right foot and left foot, match of front foot and rear foot.

二、应用技术动作以旋踢为主。三、主动攻击以旋踢为主、下压为辅，被动攻击以旋踢为主、后踢为辅。

The experimental investigation was carried out in a full baffled, flat bottom, cylindrical vessel, with 476 mm diameter, equipped with a new type propeller to push the water downward.

实验在直径为476 mm的平底搅拌槽内进行，全挡板条件，搅拌桨为CBYⅢ型轴流桨，下压式操作。

He jammed the line down hard on the edge of the boat, Unwinding the rope from my hand, I hitched it around a seat.

他用力把绳索向下压到船帮的边上。我把绕在手上的绳索解开并把它栓到一个座椅上。

The pressure moved down until the hilts locked together, and Elias' and Josua's faces were merely inches apart.

两剑向下压去，直到两只剑柄别在一起， Elias和Josua的脸相距只有几英寸。

To do this, gradually press your thighs down while keeping your heels on the floor; you will notice that now the upper shinbones do not drop toward the floor.

慢慢地将大腿向下压，但同时让你的脚跟在地面上。你会发现，小腿的上部不会向地面移动了。

May complete through design calculation this mold by drawing; Because it is first drawing under, therefore cannot design the presses encircles, the pressure is supplied by the ball, so it is impossible to design mold structure with yard lumber, so designed the yard lumber and presses the circle into a body, but this will enhance to the spring request.

通过设计计算本模具可以一次拉深完成；由于是先拉深，所以很难做成下压边圈，由弹顶器提供压力，这跟模具的结构冲突，因此不得不把卸料板和压边圈设计成一体，但这将会提高对弹簧的要求，不过经过反复选用计算还是可以够满足要求的。

May complete through design calculation this mold by drawing; Because it is first drawing under, therefore cannot design the presses encircles, the pressure is supplied by the ball, so it is impossible to design mold structure with yard lumber, so designed the yard lumber and presses the circle into a body, but this will enhance to the spring request. But passes through selects the computation to have repeatedly can satisfy the request.

通过设计计算本模具可以一次拉深完成；由于是先拉深，所以很难做成下压边圈，由弹顶器提供压力，这跟模具的结构冲突，因此不得不把卸料板和压边圈设计成一体，但这将会提高对弹簧的要求，不过经过反复选用计算还是可以够满足要求的。

May completethrough design calculation this mold by drawing; Because it isfirst drawing under, therefore cannot design the presses encircles,the pressure is supplied by the ball, so it is impossible to designmold structure with yard lumber, so designed the yard lumber andpresses the circle into a body, but this will enhance to the springrequest. But passes through selects the computation to haverepeatedly can satisfy the request.

通过设计计算本模具可以一次拉深完成；由于是先拉深，所以很难做成下压边圈，由弹顶器提供压力，这跟模具的结构冲突，因此不得不把卸料板和压边圈设计成一体，但这将会提高对弹簧的要求，不过经过反复选用计算还是可以够满足要求的。

A series of large scale model tests on cyclic axial response of the single pile in silt are described in this paper. The tests are carried out by use of the large foundation and slope engineering test system of Zhejiang University. Accumulated settlement of the pile is measured for different cyclic loading levels.

利用浙江大学自行研制的大型地基与边坡工程模型试验系统开展了单桩基础竖向下压循环荷载作用下的大比例模型试验，获得了不同侧／端阻比下桩基的循环承载力及桩顶循环累积沉降。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。