上模

The paper also simulate the vibration response of frame when suspension point were changed, which indicates, through comprehensive consideration with the mode of frame, that it can get better oscillation damping affection to position the suspension points to the node of mode shape.

本文还在模态集成模型上模拟分析了发动机悬置点的变化时车架振动响应，表明通过与车架的模态综合考虑，把发动机的位置变换到车架模态振型的节点位置也有较好的减振效果。

In the part of the vibration experiments and analysis, firstly, used the simple-beam theory to estimate the natural frequency of the beam of the 20-headed computerized embroidery machine.secondly, measured the beam of its low rank natural frequency, the beams horizontal vibrating acceleration amplitude, speed amplitude and the displacement amplitude in different rev and different turn parts. Found that it is sympathetic vibration, which bring on the thread-broken rate rise rapidly. On this base, established the finite element analysis modle of the vibrating beam, and took on hamonic analysis and modal analysis with the mold. The rusult of test and analysis offer the basis for farther improvement of the computerized embroidery machine.

振动分析部分，首先由简单梁理论出发，对横梁的固有频率进行估算；接着通过测振仪器对20头电脑刺绣机横梁进行了试验模态分析和不同工况振动测试；获得了横梁前四阶固有频率和模态振型，以及在不同工作转速、不同回转部件下横梁振动的加速度幅值、速度幅值和位移幅值；找到了横梁振动加剧的原因——共振；在此基础上建立了符合实际情况的横梁有限元模型，对模型进行了模态和谐响应计算，证实了模型的可靠性，为下一步的改进设计提供了依据。

Maleic rosin has been added to the surface of wood flour in the form of monoester, i.e., the formation of esterified wood flour bearing a pendent carboxylic group. The rheological study showed that the complex viscosity η(superscript *, storage modulus and loss modulus of WF-HDPE composites decreased firstly and increased afterward and declined lastly as the dosage of maleic rosin increased, however, the viscosity of the composite melts decreased as a whole. After the modification of wood flour, the rheological properties of composite melts were improved markedly. According to the mechanical test it was indicated that, by proper treatment of wood flour with maleic rosin, the tensile strength and flexural strength of WF-HDPE increased obviously.

WF-HDPE流变学研究表明：复合材料的复合黏度η(上标*、储能模量和损耗模量随马来松香用量的增加先减小后增大最后减小，但体系的黏度和模量总体呈下降趋势，木粉经马来松香改性后复合熔体的流变性能显著改善，这不仅有利于提高复合材料的成型加工效率，而且适当的马来松香处理也能够提高复合材料的拉伸强度和弯曲强度，后者被静态力学试验结果所证实。

Using ethyne as source gas, CNTs were successfully synthesized by CVD method. By comparing different synthesis technics, the influences of parameter to the grow of CNTs, such as catalysts, growth time, reaction temperature and ratio of all kinds of carrier gases were investigated. The results showed that the influence of carrier gas, reaction temperature, and the growth time on synthesis of CNTs was significant. In conclusion, a better condition for carbon nanotube growth was obtained. Through analyzing Raman Spectrum of samples, GM and SWNTs' characteristic peak-RBM was indicated.

采用乙炔为碳源、氢气和氩气为载气，利用气相催化热解法在AAO模板上成功的制备出了纳米碳管，用TEM，SEM，EDS，Raman等表征方法研究了生长温度、裂解时间、载气含量和不同催化剂对碳纳米管的石墨化程度、产物形态的影响，指出了单壁碳纳米管的特征振动模式—径向呼吸振动模以及拉伸振动模式G模，缺陷导致的D模，并采用蒸金后的样品进行了场发射的测试，得到了F-N曲线，与理论符合较好。

Finally, simulation software was developed with Visual C++ and Delphi for 2D molding analysis of MIM, which affords facilities for the quality forecast of 2D thin wall parts and optimal design of mold and process parameters. In the research of molding performance of MIM feedstock, for the shortcoming of capillary rheometry, it was propounded that using spiral mold test molding performance of feedstock, and a set of spiral mold was creatively designed with quickly exchange gates and closed mold cavity. With the spiral mold, an orthogonal experiment was made on getting regress equation of flow length L〓 of the heavy alloy feedstock. Then the rule of L〓 varying with Q〓, P〓, and ΔT〓 was discovered. Q〓 ranks first in the influence on process parameters of molding performance, P〓 and Δ T〓 second. Therefore the injection rate Q〓 should be controlled primarily to improve the flow performance of feedstock.

在MIM喂料注射成形性能研究方面，针对毛细管流变仪测试法衡量流动性能的不足，提出使用螺旋线模具测试喂料熔体的注射成形性能，创造性地设计了一套可快换浇口，模腔封闭的螺旋测试模，并在螺旋测试模上采用正交实验设计，得出了高密度重合金喂料流动长度L〓的回归公式，揭示了L〓随Q〓、P〓、△T〓和S〓的变化规律，并得出工艺参数对成形性能影响的强度顺序为Q〓最大，P〓与△T〓其次，因而改善喂料流动性能应优先控制注射速率Q〓。

On basis of the analysis for cores and well-logging, the authors have thoroughly studied the sedimentary facies types and characters of Chang 6 oil-bearing formation of the Baibao region with casting thin sections, SEM, trace elements and porosity and permeability analysis and a great deal of indoor testing data. The authors propose that the sedimentary facies type of Chang 6 oil-bearing formation of the Baibao region is a sublacustrine slump turbidite fan for the first time, and lithology is lower componential and textural maturities micro-fine feldspar sandstone primarily, with graded bedding, fluidified convolute bedding, slipping-cut and deformational structures, minitype syngenetic faults, flute cast, groove cast, load cast and other turbidite sedimentary facies signatures.

作者在岩心描述和测井分析基础上，结合铸体薄片、扫描电镜、重矿物、微量元素和孔渗分析等大量测试资料，对该地区长6油层组沉积相类型及特征进行深入研究，首次提出白豹地区长6油层组属于湖底滑塌浊积扇沉积体系，岩性以成分和结构成熟度均偏低的微－细粒长石砂岩为主，具粒序层理、液化包卷层理、滑动截切和变形构造、小型同生断层、槽模、沟模和重荷模等浊积沉积相标志。

The study covers the vertical displacement distribution character of each mode of Rayleigh wave, theoretical dispersion curve character of multi-modes Rayleigh wave and the characters of the max-mode Rayleigh wave dispersion curve in different layers structure, which are velocity increasing with deep, high velocity layer within underground, low velocity layers within undergroan and high velocity surface layer, within the depth of 15 meters.

研究了地层速度随深度递增型、地层中有硬层或软夹层型、表层为高速的公路型等4种地层结构在15m深度内，瑞利面波各阶模态的位移幅度分布特征、多阶模态面波的理论频散曲线特征以及不同地层结构上的&最大模&面波频散曲线的特征。

To satisfy the peoples demand for the special shoes of themselves and solve this contradiction, on the basis of Reverse Engineering, a method to design the shoe-tree, which based on feature and restriction, is proposed. The content of this paper places emphasis on constructing the feature-based model of foot, predigesting the data of feet, reconstructing the new model of the special feet and developing the prototype system.

针对人们对个性化鞋的需求，本文在逆向工程的基础上，在鞋楦的设计过程中首次提出了一种基于特征和约束的新思路来进行脚模的制取，并侧重于脚模特征模型的建立、脚型数据的简化和脚模曲面的重建等内容的研究，开发了用于重建脚模曲面的原型系统。

A drawing die,a trimming and piercing die and a flanging and restriking die for the precision shaping of the part were designed by using AutoCAD and UGII.

在详细分析车门内板结构及工艺特点的基础上，确定零件的成形工序，以AutoCAD及UGII为辅助工具，设计出车门内板成形所需的拉深模、修边冲孔模和翻边整形模，不仅保证了加工精度，同时也缩短了生产周期，降低了成本。

Slip-form construction is due to coordination of the construction trades, so during the construction process, the various types of jobs must be the rational allocation of staff, in general, the sliding mode is two shifts, working 12 hours for the class, usually in the operating platform include: concrete work, woodwork, sliding mode, electrician, both inside and outside the hanger has close-ray personnel, above there is a crane driver, the use of pumped concrete, as well as pipeline maintenance personnel, in addition to the basis of sliding speed of erection Master runway at any time.

由于滑模施工是多工种相互配合的施工，所以在施工过程中，各工种人员一定要合理配置，一般来说，滑模是两班制，工作12个小时为一班，通常在操作平台上有：混凝土工，钢筋工，木工，滑模工，电工，内外吊架上有收光人员，上边还有一个塔吊司机，采用泵送混凝土时，还有管道维护人员，此外还有架子工根据滑升速度随时搭设上人跑道。

The concept of equivalent rotationally rigidity is offered and the formula of rotationally rigidity is obtained.

主要做了如下几个方面的工作：对伸臂位于顶部的单层框架—筒体模型进行分析，提出了等效转动约束的概念和转动约束刚度的表达式。

Male cats normally do not need aftercare with the exception of the night after the anesthetic.

男猫通常不需要善后除了晚上的麻醉。