上模

It holds that, by means of logic inference,"x believes p" can be interpreted as "x thinks that p is true". By the same token, the system of the Logic of Belief can-be established, on the basis of the logic of its classical proposition, by adding the modal auxiliary "should "before t...

作者认为，从逻辑的观点出发，可以简单地将&x 相信 p&解释为&x认为p是真的&，与之相对应，信念逻辑系统可以在经典命题逻辑的基础上加入模态词&应该&而得以建立。

It holds that, by means of logic inference,"x believes p" can be interpreted as "x thinks that p is true". By the same token, the system of the Logic of Belief can-be established, on the basis of the logic of its classical proposition , by adding the modal auxiliary "should "before the verb "believe".

作者认为，从逻辑的观点出发，可以简单地将&x 相信 p&解释为&x认为p是真的&，与之相对应，信念逻辑系统可以在经典命题逻辑的基础上加入模态词&应该&而得以建立。

For the same quantity of module, using well transparent and well-proportional faceplate can acquire high luminous intensity.

在模组数量相同条件下，使用透光性和混色性好的面板可在其表面上获得较高的光照度。

The results show that the temperature of the alloy gradually decreases from the casting mouth to the exit in the roll-shoe gap, and the isothermal line deviates from the shoe side to the roll side.

结果表明：辊靴型腔内合金的温度从入口至出口逐渐降低，合金等温线向工作辊偏移；随着浇注温度的降低，辊靴型腔内半固态区间逐渐增大；为了获得优良的半固态金属浆料，确定浇注温度为710~770 ℃；合金在辊靴型腔内层流运动时，越靠近工作辊内表面，合金的运动速度越快；随着挤压模具扩展角的增大，挤压模具出口型材宽度上中心与两侧边部合金的温度差减小；半固态合金进入模具后呈辐射状逐层向前推进填充模具扩展腔，最后再逐渐向模具出口合拢；为了改善模腔内金属流动速度的不均匀性，扩展角以45为宜。

Based upon the data of modal analysis for the plate in vacuo by finite element method and properly dealing with the integral at sin-gularity, the value of NAVMI is obtained by discretizing the integral.

在真空中模态的有限元方法分析数据以及采用适当方法处理奇点积分的基础上，应用离散积分计算了无量纲附加虚质量增量的值。

Geometric continuity is less strict than mathematical continuity. G0 and C0 are equivalent, that is, the segments are positionally continuous. G1 implies that the tangent vectors are equal in direction, but not magnitude. G2 implies the curvature is the same, but the second derivatives are not.

几何连续性没有数学连续性严格。G0 和 C0 的意思相同，即段在位置上连续。G1 意味着切向矢量的方向相同，但模量不同。G2 意味着曲率相同，但二阶导数不同。

Geometric continuity is less strict than mathematical continuity. G0 and C0 are equialent, that is, the segments are positionally continuous. G1 implies that the tangent ectors are equal in direction, but not magnitude. G2 implies the curature is the same, but the second deriaties are not.

几何连续性没有数学连续性严格。G0 和 C0 的意思相同，即段在位置上连续。G1 意味着切向矢量的方向相同，但模量不同。G2 意味着曲率相同，但二阶导数不同。

Tip: Turn the cake upside down out of the tin to serve. You could dust it with some icing sugar if you like.

贴士：将蛋糕出模后，可以在表面洒上一些糖霜做装饰。

The fully inseparable bright tripartite entangled state was experimentally generated using the NOPA at deamplification and the linear optical system consisting of polarization beam splitters and half wave plates. The variances of the sum of the amplitude quadratures of the three obtained optical modes and the relative phase quadratures among them is respectively 3. 28dBm and 3. 18dBm below the corresponding Shot Noise Limit.

利用运转于参量反放大状态的NOPA和偏振分束棱镜及半波片，从实验上产生了完全不可分的明亮三组份纠缠态光场，所产生的纠缠态具有三模正交振幅分量和与相对正交位相分量差的起伏方差低于散粒噪声极限的特性。

The machine's minimal footprint and low weight, thanks to a compact dualplaten clamping system, mean maximum energy efficiency, and recordbreaking dry cycle time of just 2.6 seconds.The duo 500 pico is thus the fastest dual platen machine on the market - despite its comparatively low energy requirements.

锁模单元采用紧凑的两板式设计，占用空间小，意味着最大的能量效率，破纪录的乾燥循环周期仅仅为2.6秒。duo 500系列能耗非常低，且是目前市场上最快速的两板机械。

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时，滚道或滚动元件褪色是很常见的特征。