上模

From these simulation results, we analyze and discuss the influence of cavity boundary on Q factors of WG modes. Since there is scale size limitation due to diffraction limitation in microdisk, we also propose a novel design of photonic crystal circular-shaped (CD2) microcavity with well-sustained WG mode. We will apply the same optimization method on this microcavity named photonic crystal microflower CD2 (MFCD2) microcavity. And then this design is realized by a series fabrication processes and the measurement results will be analyzed and discussed.

由於微碟型共振腔在优化会有体积上的限制，故我们在这部分也提出一具有耳语廊模态之光子晶体修正共振腔，我们以相同的讨论结果作基础，将Q值最佳化的对象换成在小体积时也能有良好Q值表现的光子晶体，成为花型拓朴光子晶体共振腔(Photonic Crystal Micro-Flower CD2 Microcavity， PC MFCD2)，接著藉由制程方法实现该设计，并讨论其量测结果。

At present, main production: 6300T following various forging presses: hot forging press, cold and warm forging presses, cold extrusion machine; Trimming presses; closed single-point, double point press; high-speed precision bar cutting machine and forging, stamping production lines with hundreds of product variety.

目前主要生产： 6300T以下的各种锻造压力机：热模锻压力机、冷温锻造压力机、冷挤压机；切边压力机；闭式单点、双点压力机；高速精密棒料剪断机和锻造、冲压生产线等上百个产品品种。

The part of feature retrieval proposed a three-layered framework for multi-feature video retrieval which was composed of presentation, logic and transaction layer.

SupEye系统在分析MPEG-7标准的基础上解决了视频特征与用户检索特征的分离、样例查询中的特征分析以及多模态查询的结果融合问题。

The system through the temperature examination electric circuit sensation greenhouse big awning temperature change, gives monolithic integrated circuit processing through a/d conversion, through keyboard hypothesis upper limit temperature and lower limit temperature, when the greenhouse big awning temperature is lower than the hypothesis the temperature lower limiting value, start heater unit to greenhouse warming, when the greenhouse big awning temperature is higher than the hypothesis in the temperature the limiting value, stopped heating up, has realized the greenhouse big awning observation automation.

系统通过温度检测电路感知温室大棚温度变化，通过模数转换送给单片机处理，通过键盘设定上限温度和下限温度，当温室大棚温度低于设定的温度下限值时，启动点暖风机给温室加温，当温室大棚温度高于设定的温度上限值时，停止加热，实现了温室大棚测控的自动化。

Advanced construction technology and the capacity of general contractor Yajisha Bridge Ping vertical swivel General Xinguang bridge construction technology for upgrading the technology of hydraulic synchronization Balinghe Bridge Mobile slipform construction technology company at technology and equipment, management capabilities, are a modern highway construction general contracting capabilities.

先进施工技术与总承包能力丫髻沙大桥平竖综合转体施工技术新光大桥液压同步提升技术坝陵河大桥移动滑模施工技术公司在技术力量和设备、管理能力上，都具备了现代化高速公路施工总承包的能力。

In this study, we use the thermoelectric cooler whose surface temperature can be controlled by adjusting the direction and magnitude of its current to improve the cold stage and cooling system of a cryomicroscope system. The temperature control circuit and the integrated software were also elaborated to make the cryomicroscope a modular system which is convenient to use.

本研究利用调整热电致冷晶片的电流大小与方向即可控制表面温度升降之特性，将其应用於低温显微镜系统的冷冻台及冷却系统改良设计，同时配合温控电路与软体程式达到升降温之控制，最后并将整个系统模组化以增加使用上的便利性。

The effect of punch virtual velocity and sheet virtual density on the sheet strain energy was studied in this paper.

从理论上分析了凸模虚拟速度和板料虚拟密度对薄板变形能的影响。

A probability calculation formula used for the cavity dimension of injection mold is derived on the basis of analysing the variation rule of plastic shrinkage rate, and a quantitative relation among the variation of plastic shrinkage rate, plastics dimension tole-rance, manufacturing tolerance and wear allowance is discussed.

文摘：在分析塑料收缩率波动规律的基础上，导出了注塑模成型零件工作尺寸的概率计算公式，讨论了塑料收缩率波动范围、塑件尺寸公差、制造公差以及修模裕磨量之间的关系。

Second, a novel technique to produce a soft roller mold has been developed. A PC micro-lens mold is bent around a carved roller to form a shell-shaped cavity, and then PDMS is poured into it.

其次是滚轮式微透镜阵列软模之制作：将PC微透镜阵列薄膜包覆在刻沟矽胶滚轮上以形成一空穴，并注入PDMS溶液，待固化成型后直接制作出大面积之微透镜阵列滚轮模具。

The theory and methods of ship's hydrodynamic pressure field are also studied, including halfrotator model and shallow-water inferior-critical model.

深入研究了水压场建模的理论和方法，包括回转体模型和浅水亚临界模型，用实测数据对回转体模型和浅水亚临界模型进行验模，为不同条件下选择水压场模型提供了一定的理论依据，并在实测数据的基础上对模型进行了修正。

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时，滚道或滚动元件褪色是很常见的特征。