上模

The notion of the adjoint operator of amodule homomorph ism defined on a densely submodule of a comp lete random inner p roduct module is introduced and discussed, in particular the closedness of adjoint operators is p roved.

摘 要 对定义在完备随机内积模的稠子模上的模同态引入了共轭算子的概念并讨论其基本性质，尤其证明了共轭算子的闭性。

A fan-shaped aperture mask was designed, the aperture mask cooperate with a 3-axies worktable, makes up the micro-drilling system.

设计了扇形掩模，依据三轴联动加工台，设计了掩模钻孔加工系统，在此基础上研究了掩模旋转钻孔的加工参数。

The latter is essentially derived from the geometric realization of Happels triangulated equivalence between stable module category of repetitive algebra and bounded derived category of finite dimensional algebra. In terms of this realization, we deduce that the Lie algebra realized by derived category of a finite dimensional algebra is isomorphic to the Lie algebra realized by stable module category of the corresponding repetitive algebra.

后者本质上是Happel关于重复代数的稳定模范畴和导出范畴的三角等价的一个几何实现及其应用，使用这种几何实现，我们可以证明在重复代数的稳定模范畴上定义的李代数同构于相应的导出范畴上实现的李代数。

The aim of this note is to develop the theory of corings and Galois theory for weak Hopf algebras, then we get some corresponding results about weak Hopf algebras.

弱Hopf模可以看成是一个上环上的余模，这就意味着Galois上环的一般理论能够运用于弱Hopf代数。

The shortcoming of ordinary multimode Y branch optical power splitter is that the branch characteristic strongly depends on the excited modal distribution. Different input conditions including different input modes and different input positions will excite different modes and different intensity distribution of these modes in highly multimode waveguides. The interference of these modes will contribute to distribute unstably, i.e.

多模Y分支器件的设计中存在一个共同的问题，即随着光入射条件的不同(包括入射光的模式不同和输入进波导端面位置不同等)，多模波导中所激励起的模的数目以及各个模之间的功率分配也各不相同，激励起的多个模式之间总是存在着不同程度上的相互干涉影响，从而最终影响功分器的分束均匀性。

End users and Original Equipment Manufacturers look to Mate for innovation in a wide range of products such as punch holders, die holders, cartridges, multi-tools, tooling for rotating stations, tooling for special shapes, knockouts, louvers, clusters, countersinks and more.

最终用户和原装设备制造商与Mate之间保持着良好的沟通，在我们广泛的产品领域内不断探讨技术上的革新与创新。这些产品诸如上下模座，套，多子模，旋转工位模具，特殊形状模具，敲落孔模具，百叶窗，集合模，沉孔模等等。

The company also produced a screw die: the main mode, line mode, on impulse, Cutter, trimming die, for the exclusive sections of Re-header matching.

本公司还生产螺丝模具有：主模、线模、上冲、切刀、切边模等，专供各款打头机配套。

Occurs when the semi-finished, warping, especially the post-mounted corrugrted semi-finished products, immediately after the closing of embossing plate, on the paper--and there is no uniform die to tilt paper with the sponge rubber or contact, so easily make embossing plate produced by 印张 bliding, die-cutting production phenomenon.

当半成品出现卷曲、起翘情况时，特别是经过裱贴以后的瓦楞纸板半成品，放在压印平板上合压时，纸面与模切版没有均匀接触，使翘起的纸面先与版面上的橡胶条或海绵接触，这样容易使压印平板上的半成品印张产生滑移现象，造成产品模切不准。

The main products of the sticks is die-cutting on automatic die-cutting machine requires will rely on a pipe of knife more force several narrow-necked, smooth production after the die cutting machine out, in the sense of narrow-necked reflected in the die-cutting on the box of the edge is not smooth.

影响产品美观的主要原因是在平压平自动模切机上进行模切加工时需要将靠叼口边的刀多敲破几个小口，才能顺利地将模切后的成品从机器中拉出来，敲破的小口体现在模切后的盒上是边缘不光滑。

Please not that a 250 mm wide die opening will produce a film or sheet with less width since you have a "neck in" effect when you pull out the melted resin from the die before it reaches the surface of the chill roll. the width you can achieve depends on the melt strength of the resin as well as the distance between the die lip opening and the chill roll. but in general, about 80% of the die opening width can be achieved.

注意：250毫米宽开口的模头只能获得小于此宽度的薄膜或片材，因为当熔体树脂被从模头拉至冷辊上时会产生&颈缩&效应，最终获得的实际宽度依赖于树脂的熔体强度以及模唇开口同冷辊之间的距离，但总而言之，可获得模头开口宽度80%的产品宽度。

The concept of equivalent rotationally rigidity is offered and the formula of rotationally rigidity is obtained.

主要做了如下几个方面的工作：对伸臂位于顶部的单层框架—筒体模型进行分析，提出了等效转动约束的概念和转动约束刚度的表达式。

Male cats normally do not need aftercare with the exception of the night after the anesthetic.

男猫通常不需要善后除了晚上的麻醉。