上模

On base of the theory of polymeric melt filling flow in micro injection molding , the mechanism of convectional heat transfer for polymeric melt was discussed,and the effects of convectional heat transfer on the melt filling flow in micro injection molding were investigated with considering the model of convectional heat transfer coefficient.

在熔体流动理论的基础上，通过分析熔体的对流传热机理，并引入对流换热系数模型，对微注塑成型中对流换热系数对熔体充模流动进行了研究。

After the research, determined that uses forms the corbel well circle structure first in the damping well base concrete, then uses the hydraulic pressure slip form in the well circle to construct the formation continuously the plan.

经研究，确定采用先在阻尼井底部浇筑混凝土形成牛腿井圈结构，然后在井圈上使用液压滑模连续浇筑成型的方案。

1 Press ENTER for auto setting of PR. Move cross hair to die or lead provided image on the vision monitor is clear and sharp, if not adjust optical system.

按回车进入自动调节状态，移动标线到模或者线上直到图像能够清楚的被显示出来，否则调整光学系统。

In the paper, we give the method of checking form based on module 2 by searching the 16 bits Cyclic Redundancy Check Code .

本文研究了16位的循环冗余校验码CRC-CCITT在数据通信中的应用，给出了基于模2运算的查表法，实验证明：在保证了系统通信可靠性的基础上，大大提高了计算速度。

The purpose of this thesis is to develop a computer-aided virtual clay shaping system. The system includes three main parts: a glove for inputting data, a circuit module for signal processing and a windowing user-interface. Through the glove, the user can knead the virtual clay on the interface window by moving their fingers.

中文摘要本文的目的在於设计一个虚拟黏土的电脑辅助造形设计系统，系统主要分为输入装置的资料手套、讯号处理的电路模组与使用者视窗介面三部分，使用者透过资料手套，藉由手指的运动可捏塑萤幕上的虚拟黏土。

This paper first utilizes the ideological design digital controler of double-loop control based on the magnetic defi...

在此基础上，考虑系统的参数摄动及外扰等不确定因素，基于系统的不确定模型运用变结构控制理论设计离散滑模变结构控制器，并进行了必要的仿真研究。

Three actuation mechanisms of piezoelectric composite structures are studied: extension actuation mechanism, shear actuation mechanism and hybrid actuation mechanism Tip deflection of piezoelectric composite plate is analyzed for different actuator layer thickness. The research result can be used for mode control of active noise and vibration control and static shape control of intelligent structure.

研究了压电材料复合板的3种作动机制，弯曲作动机制、剪切作动机制、混合作动机制，针对粘贴在纤维板上不同厚度的压电作动层，具体分析了复合板的端部位移，研究结果对噪声和振动的主动控制中的模态控制和智能结构静态形状控制提供了一定的参考。

In static analysis, small deflection theory of circular plate and electrostatic actuating theory are adopted to simulate electrostatic-structural coupled process. In modal analysis, harmonic response analysis and nonlinear transient dynamic analysis of pump membrane, the fluid in the pump is regarded as an additional mass acting on the pump membrane to approximately substitute the effect of fluid field on pump membrane, which reduces the amount of calculation and improves simulation efficiency.

其中在静态分析中，利用圆型薄板的小挠度变形理论和微机电系统中的静电力驱动理论来模拟静电－结构耦合过程；在泵膜的模态分析、谐响应分析以及非线性瞬态分析中，把腔内的流体当作附加质量作用在泵膜上，近似代替流场对泵膜的影响，从而减小计算量，提高了仿真效率。

Then, based on a large number of static and dynamic laboratory test results, the calculation formulation on dynamic modules of shear deformation, damping ratio, dynamic pore water pressure, dynamic residual deformation are proposed, the parameters of these formulations are also given.

在此基础上，对粉煤灰进行了大量的动力特性试验研究，提出了该类粉煤灰相应的动模量及阻尼比的计算公式并给出其抗液化强度、动孔隙水压力及动残余应变的计算公式及其参数。

Two-dimensional Bernstein type operators on simplex are constructed, and a necessary and sufficient condition of uniform approximation by mem is obtained, at the same time, the degree of approximation is characterized by two-order moduli of smoothness.

并且构造出单纯形上推广的二元Bernstein型算子，给出其一致收敛的一个充要条件，同时用二阶连续模刻划了它们的逼近度性质。

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。