上模

The draft-dust system in tipper room is described based on the conclusion of model experiment.

在模化实验的基础上，叙述了通风除尘在翻车机室粉尘治理上的应用，达到减少空气污染的目的。

The surface of toilet cover, the cavity of die and punch and 3D assembly drawing and assembly scenes are realized through using the surface modeling function provided by Mechanical Desktop based on PC platform.

利用MDT的曲面造型功能在微机平台上实现了坐便器上盖塑件的造型，凹模型腔及凸模的生成。

Pumping tube pipe with a fixed part of warehouse body sliding in between the two positions embedded parts per 3m welding pipe fixed, positions on the use of rubber face effective 90-degree bend towards the two east-west positions on the sliding-mode platform with human small dump then expected, with each 300mm uniformly continuous pouring of concrete.

泵送管固定部分为钢管随仓体滑升，在两仓之间每3m焊接预埋件以固定钢管，仓上工作面内采用橡胶管用90度弯头转向东西两仓，在滑模平台上用人力小斗车接料，以每层300mm连续均匀浇筑混凝土。

Monte Carlo simulation is one of effective ways to get this kind of dosimetric parameters. In this paper, the absorbed doses at the central axis in different phantoms with inhomogeneity media and finite sizes for small field size beams were simulated with Monte Carlo code system EGSnrc, respectively.

本文利用蒙特卡罗方法模拟计算了临床上常用的点源光子束在有限宽非均匀模体中的沉积能量，研究了不同射野条件下中心轴上的剂量分布，并用剂量扰动因子定量分析了剂量增强或减弱效应的强度。

The results showed that, the accuracy of emotional recognition and preference for emotional judgment did not differ between the dysphoric and nondysphoric individuals. However, the dysphoric individuals tended to respond to non-positive facial emotions with negative cognitive-conceptual and affective schemas.

而在同等脸部情绪之辨识与判断表现的基准上，忧郁倾向个体在面对负向、甚至所有非正向之脸部情绪讯息时，明显展现认知概念与情绪向度上的负向认知基模反应倾向。

Quadratic finite volume element method s for the air pollution model in one-dimensional;2. The two-grid algorithm of the finite volume element method for second-order indefinite elliptic problems;3. A fally discrete finite volume element method is given for one-dimensional two-phase incompressible flow in porous media.

在初始网格剖分上采取分段线性函数空间作为有限体积元方法的试探函数空间，在相应的对偶网格上采取分段常数函数空间作为其检验函数空间，对一维不可压缩两相渗流驱动问题提出了全离散有限体积元方法，并得到L2-模误差估计。

Take out the dough and place it on a baking paper, covering with a greaseproof wrapper and roll out to a circle about 3mm thick.

把松弛好的面团取出，放到一张烤纸上面，盖上一张保鲜膜，用擀面棍擀成3毫米厚的薄片，然后把塔皮铺在塔模上。

Along with development of electronic technology, especially VLSI and mixed signal circuits,where there are physical or functional blocks and subnetworks which are indiscerptible in the network, it shows its practical value.

随着电子技术的发展，特别是超大规模模拟电路和模数混合电路发展，对于电路中存在着物理上或功能上具有不可分割的功能块或子网络时，该方法更显其工程实际意义。

The technical freedom permitted by the reducing machine , which allowed artists to model on a large scale while still achieving the effect of fine detail when their work was reduced , led in turn to an enormous rise of interest in medallic art .

由粉碎机所提供的技术上的自由，使得艺术家可以在大的尺度上制模完成精巧的细部效果，并同时能够减少他们的工作量，这导致了对章牌艺术的兴趣的巨大提升。

According to the fact that the otolith system is overcritically damped and the max- imum displacement of the otolith,δ〓 is independent of the dynamics, the upper limit of the Young's module of the gel layer and the estimated value of the dimensionless parameter εwere given,〓 which provided the theoretical basis for the experimental method and the theoret- ical analysis.

根据耳石层运动高度过阻尼而且最大位移〓与运动模式无关的事实，理论上给出了胶质层的Young's模量的上界估计表达式以及无量纲参数ε的参数估计式为〓从而为实验测量方法和理论分析提供了理论依据。

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。