三裂的

Then through dynamical analysis, every instantaneous acceleration distributing of slope under dynamical earthquake can be got too. According to this result, adding earthquake force to structure by way of inertial force, this paper analyses the slope stabilization by using FEM strength reduction method and gains every instantaneous safety factor and its corresponding slide. Curves of safety factors versus duration can be made by curvefitting. By safety factors versus duration curves and slides, we can value structure's quakeproof stabilization and point its slide out. By these principles, programs of FEM stabilization analysis for each moment are organized.

首先通过三维非线性有限元静力分析得到动力分析的初始应力，再进行动力分析得出边坡在动力作用下每一瞬时的加速度分布，根据每一瞬时的加速度分布的结果，将地震作用力作为惯性力加在结构上，用有限元强度折减法进行边坡稳定分析，得出在地震动力作用下每一瞬时的安全系数及对应滑裂面，拟合可得到一条安全系数随时间变化的曲线，根据这条安全系数时程曲线及滑裂面，综合得出结构的抗震稳定安全系数及对应的滑裂面。

During early middle Jurassic period, Quemocuo formation in NQB was offshore lake deposition with marine feature, in SQB was shelf deposition, which indicted that an intense rifting and sea level rising with more large range, and consequently, eroding area was shrunk and deposition area was expanded.4. According to the result of stratigraphic surface features, division and correlation, and the paleographic characteristic, Qiangtang Basin during late Triassic -early middle Jurassic period could be divided into two basin developing stages with difficult tectonic nature, remnent epicontinental basin stage in Carian -early Norian of late Triassic and rifting basin stage in middle Norian of late Triassic - early middle Jurassic period respectively.

雀莫错组在羌北盆地为近海湖泊沉积，更具海相色彩：南羌塘主要为外陆棚沉积，反映羌塘盆地再次发生较强烈的裂陷作用和较大幅度的海平面上升，形成陆源剥蚀区缩小，沉积覆盖面增大的古地理面貌。4、根据地层界面特征、地层划分与对比结果和岩相古地理演化特征可将晚三叠世—中侏罗世早期羌塘盆地划分为两个不同构造性质的盆地发展时期，分别为晚三叠世卡尼期—若利早期的残留内陆表海沉积盆地发展与消亡时期和晚三叠世若利期中晚期—中侏罗世早期的裂陷盆地的形成与发展时期。

In this paper, the 3-D finite element relocating mesh method is used to calculate the temperature field and the thermal creep stress field of spillway dam and mid level outlet dam in certain roller compacted concrete gravity dam, sensitivity analysis have been down with different parameters, such as placing temperature, the location of cooling pipe, cooling temperature, time for water supply, ascended-layer of concrete, intermissive time and different placing time, and the commendatory construction scheme have been put forward in such analysis; according by the test result on the two scheme of concrete aggregate combination (basalt as coarse aggregate and limestone as fine aggregate, basalt as coarse aggregate and basalt as fine aggregate), simulation analysis on temperature field and thermal creep stress field of the commendatory construction scheme have been down, and analysis have also been down on temperature field and thermal stress field of the two different aggregate combination, the result indicates that the spillway dam and mid level outlet dam which adopted these two aggregate combination can both satisfy the require of design crack resistance in concrete, furthermore limestone as fine is better than basalt as fine aggregate; the effect of summer water storage and winter water storage on the temperature field and thermal stress field have been analyzed, comparing with winter water storage, in summer water storage scheme the maximum tensile stress at abnormal concrete in upstream fill is decreased by 0.1～0.3MPa and there are no evidence change of the maximum tensile stress at other parts, which indicate that summer water storage is avail for the crack resistance of upstream fill; according to the simulation calculating result and comparing temperature simulation calculating results and temperature controlling measures of some similarity projects both completed and construction, synthesis appraise have been carried to the design temperature controlling measures of dam, and the temperature controlling measures of this project have been brought forward, all these have great reference value on the design of temperature controlling measures and the optimization of the construction scheme.

本文采用三维有限元浮动网格法仿真计算程序，对某碾压混凝土重力坝的溢流坝段和中孔坝段分别进行了三维有限元温度场和温度徐变应力仿真计算分析，对浇筑温度、冷却水管的布置方式、冷却水温、通水时间、浇筑升程和间歇时间、不同开始浇筑日期等参数进行了敏感性分析，在此基础上提出了推荐的施工方案；根据两种骨料方案(玄武岩粗骨料+灰岩细骨料方案；玄武岩粗骨料+玄武岩细骨料方案)的混凝土性能试验研究成果，对推荐的施工方案进行了温度场和温度徐变应力仿真计算，并对比分析了两种不同骨料情况下的温度场和温度应力，结果表明溢流坝段及中孔坝段采用上述两种骨料均能满足混凝土的抗裂设计要求，且灰岩细骨料优于玄武岩细骨料；计算分析了夏季蓄水和冬季蓄水对坝体温度场和温度应力的影响，夏季蓄水方案与冬季蓄水方案相比，坝体上游变态混凝土区域最大拉应力小0.1～0.3MPa，其他部位最大拉应力无明显变化，夏季蓄水对坝体上游面混凝土的抗裂有利；根据仿真计算成果并通过比较国内一些已建和在建的类似工程的温度仿真计算成果及采取的温控措施，对大坝的设计温控措施进行了综合评价，并提出了该工程的温控措施，对温控设计和优化施工方案具有重要参考价值。

When reached logarithm growth phase, it was poured or the medium was removed. 5 mL medium containing 10 mg/L mitocin-C was added , kept at 37 ℃, and then cultured in saturated humidity warm box with the CO2 of 0.05 fraction volume for 2 or 3 hours. It was coated with 0.1% gelatin in 6-hole plate, laid for over 30 minutes, and then threw away or the medium with mitocin-C was removed, washed with phosptat buffer for 5 times so as to remove the mitocin-C. 2 mL 0.05% trypsin digestive cells were added, and it was observed under microscope. When crevice appeared, cells became round (about 2－4 minutes), digestion was stopped by adding medium of the same volume, and blew up with straws repetitively to make it into monoplast suspension. Special-used cover glass was put in the center of cell counting chamber. Cells were sucked in by glass siphon, and cell suspension flew out at bucket of up or down-sides of counting chamber, until the cover glass was filled with fluid. Living cell were inoculated at concentrations of 3×108, 5×108, 1×109 L－1 after their number counted.

选取2～5代的小鼠胚胎成纤维细胞，待其至对数生长期倒掉或吸掉培养基，加入含10 mg/L丝裂霉素C的细胞全培养液5 mL，置37 ℃，体积分数0.05的CO2饱和湿度温箱中培养二三小时，在6孔板中加入0.1%明胶包被，放置30 min以上，倒掉或吸掉含丝裂霉素C的培养基，磷酸盐缓冲液清洗5遍，尽量除去丝裂霉素C，加入2 mL 0.05%的胰蛋白酶消化细胞，镜下观察，当细胞间出现裂隙，细胞变圆时（约2～4 min），立即加入等量的全培养液终止消化，并用吸管反复吹打，使之成为单细胞悬液，在细胞计数板中央放置专用的盖玻片，用玻璃虹吸管吸取细胞，让虹吸管在盖玻片上或下侧的计数板凹槽处流出悬液，至盖玻片下被液体充满为止。

Basal leaves 5--10; petiole 2--6 cm; blade ternate, or sometimes simple, pentagonal or broadly ovate in outline, 0.6--1.5 × 1--2.4 cm, thinly papery, subglabrous or abaxially puberulent; leaflets petiolulate, rhombic, 2- or 3-lobed or 2- or 3-partite, sometimes 1--2 × 3-sect and with ultimate segments lanceolate-linear; central lobe rhombic-obovate, 3-lobed or 3-partite.

基生叶5-10；叶柄2-6厘米；叶片三出，或者有时单，五边形的或宽卵形轮廓的， 0.6-1.5 * 1-2.4 厘米，薄纸质，近无毛或背面被微柔毛；小叶具小叶柄，菱形的，2或3裂或2或3 分裂的，有时1-2×3全裂并且具末回裂片的有时披针形线形的；中央裂片菱形倒卵形，3浅裂或分裂。

Capsule oblong, trigonous, ca. 5 mm, 3-valved; posterior valve with 1 seed, indehiscent; other 2 valves each with 2 seeds, dehiscent.

蒴果长圆形的，三棱，约5毫米，3瓣裂；后面裂片具1种子，不裂；其他2裂爿每个具2种子的，开裂。

The experiment with 4 cytoplasmic male sterile and their B-lines to examine characteristics of small vascular bundle, volume, weight, water potential of lodicules between CMS lines and B-lines and among CMS lines by using GLM and multiple comparisons, and correlation analysis was also conducted on the SVB, volume, weight, water potential of lodicules and percentage of glume-gaping grains and percentage of heavily glume-gaping grains on CMS lines.

以具有不同裂颖特性的细胞质雄性不育系福伊A、三香A、丰源A、T98A及其相应保持系为材料，对不育系间以及保持系与不育系间浆片的小维管束性状值、体积、重量、水势进行方差分析和多重比较，并对不育系浆片的小维管束性状值、体积、重量、水势与其种子裂颖率和裂颖度进行相关分析。

Sowe selected the colchicine optimum parameters were 0.6μg/ml and 6 hour culturedduration.The second, there were no significantly differences between the four groupsin 2 hour groups; and there were significantly differences between 0.2μg/ml groups and other three groups in 4 hour groups; and there were no significantlydifferences between the four groups in 6 hour groups; and there were significantlydifferences between 0.4μg/ml groups and other three groups in 8 hour groups onthe metaphases (P＜0.05), in the experiment of the effect on the mouse 8-cellembryo stage single blastomere of colchicine with different concentrations andduration by x~2 statistical analysis.

根据实验的实际情况，适宜制备小鼠4-细胞期胚胎单卵裂球染色体标本的秋水仙素的处理浓度和时间是0.6μg／ml和6小时。2、在确定秋水仙素不同处理浓度和时间对小鼠8-细胞期胚胎单卵裂球中期分裂相数影响的实验中，经统计分析，阻断培养2小时组中四个浓度组差异均不显著；阻断培养4小时组中0.2μg／ml浓度组与其他三组差异显著；阻断培养6小时组中四个浓度组差异均不显著；阻断培养8小时组中0.4μg／ml浓度组与其他三组差异显著(P＜0.05)。

The results were as follows:The first, there were significantly differences percent between 0.6μg/mlgroups and other three groups (0.2μg/ml groups, 0.4μg/ml groups and 0.8μg/mlgroups) in 2 hour groups; and there were significantly differences between0.4μg/ml groups and other three groups in 4 hour groups; and there weresignificantly differences between 0.6μg/ml groups and other three groups in 6hour groups; and there were significantly differences between 0.4μg/ml groupsand other three groups in 8 hour groups on the metaphases (P＜0.05), in theexperiment of the effect on the mouse 4- cell embryo stage single blastomere ofcolchicine with different concentrations and duration, by x~2 statistical analysis.

实验结果如下：1、在确定秋水仙素不同处理浓度和时间对小鼠4-细胞期胚胎单卵裂球中期分裂相数影响的实验中，经统计分析，阻断培养2小时组中0.6μg／ml浓度组与其他三组差异显著(0.2μg／ml组、0.4μg／ml组和0.8μg／ml组)；阻断培养4小时组中0.4μg／ml浓度组与其他三组差异显著；阻断培养6小时组中0.6μg／ml浓度组与其他三组差异显著；阻断培养8小时组中0.4μg／ml浓度组与其他三组差异显著(P＜0.05)。

So we selected the colchicine optimumparameters were 0.2μg/ml and 6 hour cultured duration.The third, there were significantly differences percent between 10 hourgroups and other three groups (4 hour groups, 6 hour groups and 8 hour groups) in0.1μg/ml groups; and there were significantly differences between 8 hour groupsand 10 hour groups, but they had no significantly differences among other twogroups in 0.3μg/ml groups; and there were significantly differences between 10hour groups and 6 hour groups, but 10 hour groups had no significantlydifferences among other two groups in 0.5μg/ml groups; and there weresignificantly differences between 8 hour groups and other three groups in0.7μg/ml groups on the metaphases (P＜0.05), in the experiment of the effect onthe mouse 4- cell embryo stage single blastomere of vinblastine with differentconcentrations and duration, by x~2 statistical analysis.

根据实验的实际情况，适宜制备小鼠8-细胞期胚胎单卵裂球染色体标本的秋水仙素的处理浓度和时间是0.2μg／ml和6小时。3、在确定长春花碱不同处理浓度和时间对小鼠4-细胞期胚胎单卵裂球中期分裂相数影响的实验中，经统计分析，阻断培养0.1μg／ml浓度组中10小时组与其他三组差异显著(4小时组、6小时组和8小时组)；阻断培养0.3μg／ml浓度组中8小时组和10小时组间差异不显著，但与其他两组差异显著；阻断培养0.5μg／ml浓度组中10小时组与6小时组差异不显著，而与其他两组差异显著；阻断培养0.7μg／ml浓度组中8小时组与其他三组差异显著(P＜0.05)。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。