一致通过

The principles are as follows:①preliminary interpretation is carried out on crosswell seismic data in depth domain to establish an accurate velocity model;②sinc interpolating function is used in depth-time conversion to realize waveform fidelity;③the recognition of surface seismic data is utilized to ascertain the reflection characteristics of crosswell seismic data in time domain;④ good spatial continuity of surface seismic data is adopted to retrieve the "hopper" defect in crosswell seismic profiles and the deficiency of lateral contrast between crosswell seismic data;⑤in fine calibration of well-side traces of crosswells and surface seismic data, coincident time-depth relation is used to match two seismic data so as to make the calibration more reasonable;⑥in multi-crosswell seismic data inversion by sparse spike inversion method, lateral restraints are strengthened to ensure the continuity of inversed wave impedance profile.

实现反演的基本原理是：对深度域井间地震资料进行初步解释；建立精确的速度模型；在对井间地震剖面进行深时转换时采用sinc插值函数实现波形保真；利用对地面地震资料的认识来落实时间域井间地震资料的反射特征；利用地面地震资料良好的空间连续性弥补井间地震剖面的"漏斗"缺陷和井间资料之间横向对比性的不足；在井间地震和地面地震井旁道精细标定中，通过一致的时深关系来实现两种地震资料之间的匹配，使井旁道的标定更加合理；在利用稀疏脉冲反演方法进行连井井间地震资料反演时，通过增强横向约束保证反演波阻抗剖面的连续性。

In this paper, Newton iteration formula for computing normal depth and critical depth was put forward by mathematical transformation of uniform flow equation and critical flow equation of circular section tunnel. Then, the relationship between the corresponding central angle and the introduced parameters was analyzed. An approximate formula for angle was obtained according to optimal uniform approximation principle. Using this approximate formula as initial value of iteration formula, a direct formula for calculating normal depth and critical depth of circular section tunnel was established after its first iterative.

该文通过对圆形断面均匀流方程与临界流方程的数学变换，分别得到其正常水深与临界水深的牛顿迭代公式，同时，通过对正常水深与临界水深对应的中心角与引入参数之间关系的分析及数值计算，利用最优一致逼近原理分别得到了正常水深与临界水深对应中心角的近似计算式，并以此近似计算式为初值，用迭代方程进行一次迭代得到了圆形断面均匀流水深与临界流水深的直接计算公式。

The sameness of postmodernism and Socrates is that they all prore the ignorance of man to the terminal truth、 terminal meaning: Socrates made a factual provementthrough nis failure to pursue the terminal meaning of the conceptions, while postmodernism made a theoretic provement through illustrating the difference 、dissemination,、 trace.

后现代主义与苏格拉底的一致之处是他们都证明了人对终极真理、终极意义的"无知"：苏格拉底通过对那些概念的终极意义的追寻的失败对此作出了事实的证明，后现代主义则进行了理论的证明，即通过论证文本意义的分延、播撒、踪迹、替补等证明其终极意义的不可获致，证明对终极意义的追寻是一个无限的过程，这恰好符合苏格拉底对话的情形，因此二者可以互为佐证。

Secondly, relations between the structuralism and physics teaching illustrate that the physics history can play the role of "advanced organizer" in improving the transfer ability. Moreover, the theory of recapitulation of physics announces the inherent similarity between the process of physics research and the process of physics conception learning. According to constructivist learning theories, the dissertation explains the process of students' learning the scientific concepts.

首先论文通过分析比较皮亚杰认知发展论和库恩科学发展论得出教育实践应与科学发展规律保持一致，应重视物理学史在物理教学中的应用，对于不同认知水平的学生和不同类型的知识应采用不同的教学方法：其次从结构主义与物理教学的关系说明物理学史在提高迁移能力上可以扮演"先行组织者"的角色；再次，通过物理文化重演理论揭示人类研究物理学的过程与学生学习物理概念的过程的内在相似性，并根据建构主义学习理论解释学生学习科学概念的过程。

The synthesis of the pentacyclic skeleton of Et-743 and the construction of the five chiral centers thereof.1. The core pentacyclic skeleton of phthalascidin was constructed with L-dopa as the starting material via thirteen steps. First, two basic synthons, the C-1 functionalized tetrahydroisoquinoline compounds 8 and N-protected Z-dopa derivative 9, were prepared from L-dopa. They were coupled via amide bond to form the dipeptide compounds 10, which were the first key intermediates. Then the primary hydroxyl groups were transformed into the corresponding amino aldehydes 11 via Swern oxidation. Followed by the intramolecular Pictet-Spengler cyclization, the pentacyclic compounds 12 were synthesized.

五环骨架的构建及五个正确手性中心的确立：1.1我们以L-多巴为起始原料，经过多步官能团保护和转化合成了基本结构单元8然后和苯丙氨酸衍生物9，通过缩合反应生成酰胺中间体10，经Swern氧化得到醛化合物11，然后再次利用分子内改良的Pictet-Spengler反应一步构建c，d两环，得到五环骨架化合物12，最后，实现了21-位羰基向氰基的转化，得到了C-1位官能化的化合物14，化合物14不但具有和Et-743一致的五环骨架，而且分子中五个手性中心立体构型也与其完全相同：其中，3，位和13，位的手性中心由原料L-多巴带入，而1，位，11，位和21，位手性中心则通过不对称诱导而确立。

The results were as follows: 1.Inoculated on the induction medium at the late uninucleate stage,the microspores could initiate embryogenesis by first divisions in both symmetric and asymmetric patterns,but the former was predominant.

通过观察玉米小孢子胚胎发生的细胞形态学特征，发现：离体培养条件下单核后期的花粉可以通过均等分裂和不均等分裂两条途径形成胚状体，与前人的研究结果一致。

In order to investigate buckling mode, buckling load and failure mode of structure, shear experiments were conducted for stiffened thin-walled composite plate. Finite element method was also used to analyze the buckling behavior of that composite structure. Analysis results reveal buckling mode and buckling loading of finite element analysis are accordable with experimental results.

通过对复合材料薄壁加筋板结构进行剪切载荷下的屈曲试验研究，得到结构的屈曲模态、屈曲失稳载荷以及破坏形式，并通过有限元方法对结构的屈曲进行数值分析，分析得到的复合材料薄壁加筋板结构的屈曲模态和试验结果一致，屈曲载荷与试验结果吻合较好。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area;2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support;3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier;4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling;5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene PolymerizationIn this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that:1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS;2.co-mlling time had no obvious effect on the texture of support after 12 hours;3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现；3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布；4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒；5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明：1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致；2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响；3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area; 2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support; 3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier; 4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling; 5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene Polymerization In this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that: 1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS; 2.co-mlling time had no obvious effect on the texture of support after 12 hours; 3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现； 3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布； 4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒； 5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明： 1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致； 2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响； 3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Several anti-tumor cell lines and carbonic anhydrase Ⅱ model were established. More than 10000 compounds and extracts from plants were screened using these models and about 10 compounds showed strong inhibitory activities. Two species of plants Inula helianthus-aquatica and Saussurea deltoidea were chosen to investigate chemical and bioactivity constituents based on the results of screening of extracts and fractions. 58 compounds were isolated and identified from these two plants, 6 compounds were found to be new and 14 compounds showed anti-tumor activities. We also studied the anti-tumor mechanism of the compound bigelovin isolated from Inula helianthus-aquatica. Bigelovin was found with apoptotic activity against cell line U266 by lowering the amount of important transcription factor E2F-1 which inhibits the cell cycle at G0/G1 stage. Docking study on 7 natural new phenolic inhibitors of CA Ⅱ and 3D-QSAR study on 61 sulfonamide inhibitors of CA Ⅱwere also investigated. The calculated results were in good correlation with experimental results.

基于以上两种重要疾病和研究组方向，本论文工作开展了多个肿瘤细胞株和碳酸酐酶Ⅱ靶标模型的建立和筛选工作，累计筛选1万多个/次样品，发现10余个活性较强化合物；从粗提取物筛选结果中选取两种抗肿瘤活性强的菊科植物水朝阳旋覆花(Inula helianthus-aquatica)和三角叶凤毛菊进行了系统化学和活性成分研究，分离鉴定了58个化合物，发现6个新化合物和14个抗肿瘤活性化合物；通过合作对水朝阳旋覆花中活性较强的bigelovin进行了抗肿瘤作用机制研究，发现它可能是通过降低G2期重要的转录因子E2F-1，致使细胞周期阻滞在G0/G1期，引起多发性骨髓瘤U266细胞凋亡；开展了7个新的天然酚类CAⅡ抑制剂的对接研究和61个合成的系列磺酰胺类CAⅡ抑制剂的3D-QSAR分析，结果表明计算与实验一致。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。