查询词典 z axis

The z-axis anisotropic dielectric layer focusses an electric field at each of the electric field sensing electrodes.

所说Z－轴各向异性介电层将电场聚焦到各个电场检测电极处。

The PPLN crystal is 20 mm long and periodically poled along the z-axis by using external electric poling technique.

PPLN晶体长20 mm，利用外加电场极化法制作，极化沿晶体的z向进行。

Once you establish the direction of the head, I usually check it in the Preview window to make sure the front of the head is facing out the z axis and right side up. If it isn't, reposition and press, Store.

一旦确定了头部面对的方向，我通常都会在预览窗口检查是否面对Z轴的正确位置，如果不是的话，调整一下然后按Store键。

Both numerical control induction machine tool X-Z axis and slew workbench of part drive by numerical contral, the coil feed motion is drived with servo motor which joins to ball screw assemblly to carry out.

数控感应淬火机床X-Z轴和工件的回转工作台均采用数控驱动，感应头的进给运动通过伺服电机带动滚珠丝杠来实现。

Since the machine was designed to focus on heavy load, rack of large steel, Z-axis stroke big, so not only do a small engraving machine technology, but also high-speed cutting thick plate, a feed volume of up to 20mm-30mm, which is carving machine not impossible process.

由于机器设计注重重型负载，机架钢性大，Z轴行程大，因此不仅可以做小型雕刻机的工艺，更可高速切割厚的板材，一次进刀量可达20mm－30mm，这是雕刻机根本做不到的工艺制造。

Machine Annex: exhibition Taiwan precision milling machine accessories, Former Punch Punch Grinder Wheel Dresser Former perspective, tools, Motorola precision block precision regulated sinus oidal magnetic sucker units, wire-cutting ceramic fixture find Taiwan Li edge browser-hoon, Z axis configuration, and the Taiwan Universal Grinding Tools eagle, the British electronic control of permanent magnet sucker clamping devices, permanent magnet hoist, and the Association vice-wai, Jingshan universal clamp group Taiwan trade giant pneumatic tapping machine, the Kuril chuck, chuck soft claw claw hardware, hydraulic chucks

机床 附件：台湾精展铣床磨床配件，冲子成型器冲子研磨机砂轮修整器角度成型器，工具万力精密块规精密吸盘正弦磁台，线切割夹具台湾丽勋陶瓷寻边器，Z轴设定器，台湾鹰牌工具万能磨刀机，英国电控永磁吸盘夹紧装置，台湾仪辰ECE磁性工具，永磁吊重器，协威虎钳，京山万能夹具组台湾贸巨气动攻丝机，千岛卡盘，卡盘软爪硬爪，油压夹头

In this system the motion controlling centers upon regulating the speed of wire feeding and movement of lead screw in each direction.Four motors separately drive the wire-feeding tape roll and the lead screw move respectively following their directions of X, Y, Z axis. If all the motors are controlled by 89C51 directly,it will rise great difficulty for software and hardware implementation. So the suggested solution is to combine the microcomputer with stepper motor driver and control of their motion.

在本系统中运动控制的关键即送丝与各丝杠移动的调节，由四个电机分别驱动X，Y，Z轴方向的丝杠行走以及送丝操作，运动控制部分如果用89C51直接驱动各电机则在软件和硬件实现上都比较困难的，所以选用单片机与步进电机驱动器结合起来控制它们的运动。

CNC surrounding attachment: all kinds of holders, body, chuck, chuck handle, adjustable boring hole, and tapping devices, BT pull bolt head, Tool Cart, spindle cleaning rods, lock knife blocks, all kinds of Z-axis settings Miriam, 3D form, eccentric type, photoelectric devices, such as edge finding.

CNC周边附件：各式刀杆、本体、夹头、夹头柄、可调式搪孔器、攻牙器、BT螺栓拉头、刀具车、主轴清洁棒、锁刀座、各种Z轴设定仪、3D表、偏心式、光电式寻边器等。

In the left tool carriage, the ball leadscrew、the servo motor and single gear reducer were displaced,and the coordinated movement about X and Z axis could be implemented by semi-closed loop control of SINUERRIK 802D numerical system.

左刀架采用滚珠丝杠、伺服电机和一级齿轮减速，并利用SINUMERIK 802D数控系统的半闭环控制实现左刀架的X轴和Z轴联动控制，机床改造后，大大扩大了机床的加工范围，同时提高了生产效率和加工精度。

The next step will be to add a DVE tool to rotate the image down to a simulated ground plane. After this we'll animate it spinning on the Z axis to add a little excitement to the backdrop.

下一步我们将增加DVE节点来旋转图像模拟地平面，然后我们会旋转它的Z轴来给背景增加一点趣味。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。