查询词典 x-axis

The equipment is used for five axis machining of various structure parts for aviation and with complex surface.

设备用途及基本要求：用于各种复杂型面的航空结构件的五轴加工。

By making a comprehensive survey, the writer classifies new campus eco-construction into core, axis and complexness.

综观我国高校近年来的建设情况，本文将高校新校区生态规划结构归纳为核心型、轴线型、匀质型三类。

You can use a datum axis to create datum planes, to place items concentrically, or to create radial patterns.

你可以利用一个坐标片面作为你的草图的参考特征，或者是建立和定位的依据。

The model used did not allow displacements in the x-axis direction on the face of the concrete block.

所用模型不能在混凝土砌块表面x轴方向上产生偏移。

Based on the condensability of liquid,the structure used in multi-axis force sensor of underwater robot aimed at balancing hydraulic pressure was investigated and an iteration algorithm used to calculate the pressure difference between in and out of the sensor was put forward,which applied the pressure balance method of film .

以水下机器人所用多轴力传感器的压力平衡结构为研究对象，基于液体的可压缩性，提出了膜片式压力平衡传感器内外压力差的迭代算法，推导出了膜片式压力平衡法的内外压力差、额外轴向力及相关公式。

A design method of non-perpendicular pitch cone of the honing wheel is presented in this article. By adjusting the distance from the contact point of pitch cones to the axis of honing wheel, the relative velocity between pitch cones is ensured to be in the direction of the tooth trace of the gear.

提出了用于珩磨螺旋锥齿轮的非正交珩磨轮节锥面的设计方法，通过调整节锥面切点到珩磨轮轴线的距离，保证了节锥面之间的相对速度恰好沿着齿长方向。

Analyzing the honing principle of spiral bevel gears based on crossing-axis transmission, the mathematical model of the relative sliding speed of the contact point between honing wheel and gear is achieved. It is determined that the pitch cone of honing wheel depends on the number of teeth in the honing wheel and the angle between the common normal of pitch cones and the plane parallel to both gear and honing wheel axes.

分析了基于交错轴传动的珩齿原理，导出珩磨轮与被珩齿轮在啮合点处的相对滑动速度的数学模型，根据该数学模型可以判定珩磨轮的节锥面是由珩磨轮齿数、公法线和与珩磨轮轴线平行的平面夹角所确定。

The bearing of planetary axis includes cone-shaped roller bearing and the needle bearing that carry cage.

行星轴的轴承包括锥形滚柱轴承和带保持架的滚针轴承。

Then, using these data tables to graph through figure guide and get single latitude positive axis conic projection figure and histogram about length distortion with latitude.

并介绍了如何利用求得的数据表使用EXCEL软件中的图表向导进行绘图，绘得正轴单纬圆锥投影图，即大地坐标的经纬网展布图及长度变形随纬度变化的关系柱状图。

Firstly, by using the function of EXCEL software and choosing the appropriate expression to calculate and get positive axis single latitude conic projection plane right-angle coordinates data table and length distortion data table about latitude.

根据实践经验，以经度97°~108°；纬度23°~34°为研究工区，用正轴切圆锥投影模型为例，介绍利用EXCEL软件中的公式对地图制图中的数据进行运算处理，求得正轴单纬圆锥投影平面直角坐标数据表，以及长度变形随纬度变化的关系数据表。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48