查询词典 x-axis

The main root axis from which smaller root branches arise; a root system with a main root axis and smaller branches, as in most dicots.

具有侧根的主根轴；由主根和侧根组成的根系，见于大多数双子叶植物。

The main root axis from which smaller root branches arise; a root system with a main root axis and smaller branches, as in most dicots.

直根 Taproot 具有侧根的主根轴；由主根和侧根组成的根系，见于大多数双子叶植物。

For five-coordinate NC end milling, the author gives the equation of tilt angle, the optimum algorithm of tilt angle, the analysis of machined errors, the compensative algorithm for cutter axis tilt error, and the formulae of feed length, feed width and cutter axis swing angle.

推导了五坐标端铣数控加工中的后跟角计算公式，提出了后跟角的优化计算方法——刀盘周边7点干涉检验法，分析了各种加工误差，提出了刀轴摆动误差补偿方法——刀具切触点偏置法，给出了走刀步长、切削宽度以及刀轴摆角的计算公式。

The feed motion is projected into each feed axis, and based on its mechanical model(motor driving torque/force, Inertial force and cutting force), the constraint relationship between feedrate, feed acceleration, and feed drive capabilities and toolpath geometric characteristics is derived. With this constraint model, the acceleration and deceleration of each axis can be limited within its capability.

将进给运动分解到各运动轴，根据机床进给轴的力学(电机驱动力／力矩、进给系统所受的惯性力及切削力)模型，推导了多轴联动加工时进给速度、加速度与各进给轴驱动能力以及加工路径几何特性之间的约束关系，使得加工过程中机床各运动轴的加减速始终处于其加工能力范围内。

These issues include: the main axis may cause a similar problem with the main axis of the fault has affected the accuracy of bending; workpiece clamping possible problem is that the workpiece center and the main discrepancies, which could lead to instability in rotating workpiece; servo motor failure: the feed system Ball Screw bending and oil do not lead to rust long run can also be caused by poor, such as the same issues.

这些问题包括：主轴主要可能引起类似问题的故障有主轴弯曲影响精度；工件装夹方面可能的问题是工件中心和主轴不一致，由此可能导致工件转动不稳；伺服电机出现故障：进给系统中滚珠丝杠的弯曲和长时间不上油导致生锈运行不畅等也可能引起相同的问题等。

As a result of the transmission of traction roll will to a certain speed, tension from the pull-out feeding axis and force it into the business card printing and membership card Studio, this part of the tension than business card printing and membership card Studio tassion, usually attached to a feeding on the axis of brake to control tensility.

由于牵引辊的传不静不兵塑料薄膜以必不退的不缓率、压辛从给料轴拉不入并送入制卡和会员卡制息部，这局部的压辛给不小于制卡和会员卡制息部的压辛，凡是用不停在给料轴上的制不静器来把持压辛。

The gimbal ring and drive axis is impossible to coincide with the centre axis of gyroscope completely during the assembly process.

摘要在动力调谐陀螺的装配过程中陀螺和平衡环的中心轴总是不可能完全与驱动轴轴线重合，因此存在一定的安装倾斜角。

Based on the drawbacks of the traditional two-axis gimbals, a new improved four-axis gimbals is introduced.

分析讨论了传统光电吊舱两框架结构的缺点，接着详细给出了改进的四框架控制系统。

Aim and Methods\ Three methods are analysed and compared for measuring the lateral deflection of gun bore axis from firing plane and the deviation of the sight line from the barrel axis, according to the results measured in practice. Results\ The tested data show that this new method is accurate.

引 言在多次火炮总装测量检查中，我们发现用炮口瞄准仪测量&炮膛轴线偏离射面的偏离角&与&瞄准线偏移&和用经纬仪、炮口坐标尺测量这两个项目有一定的差别。

Based on the processed accessory, the number, the position and the machining data of the holes and the form of the principal axis are determined; The driving way of the headstocks are drawn, the power is transmits by the methods of optimization, the driving parameter are determined, the structure of the principal axis are designed and the strength of the parts, such as the gears and the bears, are checked.

根据被加工零件确定加工孔的数量、位置、切削用量及主轴类型，拟订了主轴箱的传动方式，应用最优化方法传递功率，削减振动，确定传动参数，设计轴的结构，进行如齿轮、轴承等相关零件的强度校核计算。

The shaping method of noncircular part and the tool holder's radial motion characters in noncircular turning process are discussed in detail in the thesis.

论文详细研究了非圆零件的成型方法和加工过程中刀架的径向运动规律。

I have not really liked him,I do not like his this kind of disposition.

我没有真的喜欢他，我不喜欢他的这种性格。