查询词典 x-axis

Secondly, the cutter of the machine was studied from reducing vibration, emphasis on knives array, homeostasis. To apply "ANSYS"method, At the same time, it was known that inherent frequency of the main axis was so far higher than vibratory frequency, and the machine main axis'rotational speed won't cause sympathetic vibration.

其次，本文从减少振动入手对9LRZ-80型秸秆揉切机的关键部件切碎器进行分析，着重对动刀片的排列、动平衡等进行分析研究，并通过有限元分析，得到切碎器主轴固有频率远远大于机器振动频率，机具的转速不会造成共振的危害。

If the tangent line is extended to the horizontal axis the problem is simply a matter of comparing angles formed by the lines and the horizontal axis.

如果将曲线上某个点的切线延伸并与水平坐标轴相交，这时候问题便转化为只需要比较该切线与水平轴所形成的角度便可以确定该点为弹性或非弹性。

Depending on the axis being spacelike, timelike or null, there are three types of screw motions, the third case, i.e., cubic screw motion, is most particular because it is not a rotation together with a translation along the null axis, but a rotation together with a translation along a null curve with non-zero curvature.

依据旋转轴的向量类型，三维Minkowski空间中的螺旋运动可分为三类，其中第三类螺旋运动，即三次螺旋运动，是最特殊的。

Fetal transverse position when the longitudinal axis of the vertical longitudinal axis and the mother is the most fetal position is not conducive to giving birth.

横位时胎儿纵轴与母体纵轴相垂直，是最不利于分娩的胎位。

Child growth and development in the eye, the eye grew from a small, axial length gradually increase, if the eyeball as a sphere, it has three axes, namely, longitudinal, transverse, sagittal axis, a sphere is the length of the three-axis equivalent.

儿童的眼睛在生长发育中，眼球由小长大，眼轴逐渐增长，如果将眼球看成一个球体，它有三个轴，即纵轴、横轴、矢状轴，一个正球体的三个轴的长度相等。

Result: For all of the 100 atlases samples, in 15 samples (15%) there were skew transverse processes in abscissa axis, in 5 samples (5%) asymmetry of anterior and posterior tubercles in longitudinal axis, in 10 samples (10%) asymmetry of left and right posterior arches of atlases, in 11 samples (11%) asymmetry of vertebral foramens.

结果：100例寰椎标本左右横突在横轴上偏歪者15例(15%)、前后结节在纵轴上不对称者5例(5%)、左右后弓不对称者10例(10%)、椎孔不对称者11例(11%)。

Orient the vehicle or body in white so that its transverse axis is aligned with the axis of the acceleration device, simulating a driver-side impact.

5.3.2.2.3横向面设定1-使车辆或车壳横轴与加速装置对正，模拟驾驶侧之侧方碰撞。

D1.1 of the AISI Specification limits the maximum longitudinal spacing of connections to ... where smax = maximum permissible longitudinal spacing of connectors L= unbraced length of compression member rI = radius of gyration of I-section about the axis perpendicular to the direction in which buckling would occur for the given conditions of end support and intermediate bracing rcy = radius of gyration of one C-section about its centroidal axis parallel to the web.....

因此，AISI规范第D1.1节限定连接的最大纵向间隙为：，式中 smax =连接体允许的最大纵向间隙 L=抗压构件的自由长度 rI =工字钢对垂直于给定端承和中间肋条件下可能产生纵向弯曲方向的轴的回转半径 rcy =一段U型钢对其平行于筋的质心轴的回转半径。。。。。。。

Figure 2 shows a sample spectral mask, 47 CFR 90.210 G, with a normalized X axis to show the offset from the center of the channel and a normalized Y axis to show the unmodulated carrier output.

图2显示一个频谱遮罩的例子，47 CFR 90.210 G，X轴显示距信道中心的偏移量，Y轴显示未调制的载波输出。

According to above equations, the equivalent circuits and vector diagram in dq axis are plotted out and mathematical models described by state space in dq axis are constructed.

根据上述方程，绘出dq轴的等值电路及矢量图，得到状态空间描述的dq轴数学模型。

The shaping method of noncircular part and the tool holder's radial motion characters in noncircular turning process are discussed in detail in the thesis.

论文详细研究了非圆零件的成型方法和加工过程中刀架的径向运动规律。

I have not really liked him,I do not like his this kind of disposition.

我没有真的喜欢他，我不喜欢他的这种性格。