查询词典 workpiece

Clean up the workpiece's surface, grease spot , scrap iron and edge burr should not be existe

清理被测零件表面，不得有油污，铁屑，边缘不得有毛刺

Before the final position of workpiece on the baseplate is settled down, the possible candidate fixturing points on a planar surface may be enormous in number and hard to handle by a continuous model.

在决赛前的位置上工件基板是定居下来，可能的候选人装夹点平面可能是巨大的数量和难以应付的一个持续的模式。

Of metal, non-metallic, deburring, edge, chamfered, polished bright, and strengthen the workpiece surface during the electroplating, chemical surface treatment prior to finishing treatment.

对金属，非金属，去毛刺，飞边，倒角，抛光亮，强化工件表面在电镀，化学处理前的表面光整处理。

Introduction The chamfering performed to deburr the edge of a workpiece after the machining process is necessary to obtain workpieces with a certain quality.

工件在完成加工后，为保证工件的质量，用斜面清除工件边角的毛刺很很有必要的。

The difficulty of aluminum alloy shell workpiece with empennages was analyzed during plasticity forming, and its forming process and die designing was introduced.

分析了带尾翼铝合金壳体零件在塑性成形过程中的难点，介绍了壳体零件的成形工艺与模具设计的方法。

Regulation by the side of the block-pressed support, so that the supporting block to maintain good contact with the workpiece: by regulating the extension units in the handle, change or reduce the concentration of cutting lathe and extension units in the large gap between the extension units: in order to break them down.

可通过调节上侧支承块的压紧力，使支承块与工件保持良好接触：通过调节中拖板手柄，改变切削浓度或减少车床大拖板和中拖板间的间隙：从而加以消除。

When using an , you don't only need to adjust the perpendicularity between end plane and axes, but also need to adjust the position of four jaws to make the center of workpiece's front face coincides with lathe spindle.

使用四爪卡盘时不仅要调整端面与轴线的垂直度，还要调整四爪的位置，使工件前端面的圆心与车床主轴重合。

Studies the prediction approach of workpiece in face milling deformation.

研究端铣加工变形的仿真预测方法。

When face milling is performed, the table can be moved longitudinally to feed the workpiece under or below the cutter

铣削端面时，为了将工件送到刀具底下或下方，工作台可以纵向移动。

The shaper tool straight line advance and return movement is host motion when plane chop, that workpiece moves in the perpendicularity and host direction of motion intermittence is to feed motion.

刨削时，刨刀的直线往复运动是主运动，工件在垂直与主运动方向的间歇移动是进给运动。

We have no common name for a mime of Sophron or Xenarchus and a Socratic Conversation; and we should still be without one even if the imitation in the two instances were in trimeters or elegiacs or some other kind of verse--though it is the way with people to tack on 'poet' to the name of a metre, and talk of elegiac-poets and epic-poets, thinking that they call them poets not by reason of the imitative nature of their work, but indiscriminately by reason of the metre they write in.

索夫农 、森那库斯和苏格拉底式的对话采用的模仿没有一个公共的名称；三音步诗、挽歌体或其他类型的诗的模仿也没有——人们把&诗人&这一名词和格律名称结合到一起，称之为挽歌体诗人或者史诗诗人，他们被称为诗人，似乎只是因为遵守格律写作，而非他们作品的模仿本质。

The relationship between communicative competence and grammar teaching should be that of the ends and the means.

交际能力和语法的关系应该是目标与途径的关系。