查询词典 working surface

The change of heat absorption and outlet gas temperature of each surface and the change of working substance temperature,etc.are analyzed.

文中对各受热面的吸热量变化、各受热面出口烟气温度变化、工质温度变化等内容作了分析。

From the experimental angle, has carried on the system elaboration in literature [2],[3] to several kind of typical oscillatory occurrences, and will affect the low frequency vibration the factor to induce into the filter unit, the working substance current capacity and the type, the discharge voltage, the negative pole current capacity and the position, the wall surface pollution, the magnetic field such several factors.

从实验的角度，在文献[2]，[3]中对几种典型的振荡现象进行了系统的论述，并将影响低频振荡的因素归纳为滤波单元、工质流量和种类、放电电压、阴极流量和位置、壁面污染、磁场这样几个因素。

AbstractAIM: To study the occurrence of ocular surface diseases on staffs working in operating room and to investigate the relation between xerophthalmia occurrence and peroxyacetic acid contiguity.

目的：观察与过氧乙酸有密切接触人群的眼表情况，来分析过氧乙酸接触对干眼症发病率的影响。

According to the working procedure chart of theZH1105W diesel engine's gear cap analysis workpiece's precision, the surface roughness, thespecification, the processing spot size, the shape structure,material degree of hardness, the work piece rigidity and thedifferent of the components batch size to definite technique andtechnological process, determine aggregatemachine-tool's overall plan. Consider to theirregularity components but have high accuracy holes to beprocessing. So,"two holes at aface" is the best localization plan.

根据ZH1105W柴油机齿轮室盖的工序图分析其精度、表面粗糙度、技术要求、加工部位尺寸、形状结构、材料硬度、工件刚性及零件的批量的大小不同，确定被加工零件工艺方法和工艺过程，确定该组合机床的总体设计方案；考虑该零件表面结构的不规则性但有较高精度的孔需要加工，定位基准选择&一面双孔&是最佳的方法。

This paper is original from "On-line Measuring System for Cragged Surface on Special Working Conditions", supported by the Science and Technology Research Foundation of Anhui Province. One aim of this project is to research on the technique of measuring geometric parameters on train wheel profile applying stereovision measurement technology.

本论文所研究的课题来源于安徽省重点科研项目&特殊工况异形曲面在线检测系统&，此项目研究的目的之一是应用视觉测量技术检测火车轮轮缘踏面的轮廓几何参数。

Its mission is to acquire the knowledge needed for sustainable living and working in low-lying deltaic areas, with a focus on hydraulic and geotechnical engineering, geosciences and the integrated management of surface and groundwater and aquatic ecosystems.

沃润德教授作为荷兰皇家科学院生态学会三角洲分会的主任，该分会主要是探讨低洼三角洲地区的可持续生态需求，侧重于水文和地理技术工程，地球科学及地表水和水文系统的综合管理研究。

Positive-working imageable elements comprise a radiation absorbing compound and inner and outer layers on a substrate having a hydrophilic surface.

阳图制版可成像元件包含辐射吸收化合物和在具有亲水性表面的底材上的内层和外层。

It use two disparting surface,and its frame is fast.It use point moulding gob,so,it can fall off automatism.When it is pulled out ,the pulling pole pull the product and accomplish the pulling of its side concave . The design project is divided into two parts. The first part is about the working theory and application of a plastic injection mould, the principle of designing and the introduction of the production about plastic mould.

它采用双分型面分型，结构紧凑；采用点浇口，且浇口可以自行脱落；顶出时，由推杆和斜顶杆顶出制品并完成制品内侧凹的抽芯；模具定模上的水道以多支回路分别冷却，动模一侧的型芯由三组水道分别冷却。

Furrowing opener is one of important components in seeding and fertilizing. They often work in the soil with high moisture content. Soil adhesion on the surface of furrow opener increase the drag resistance considerably, makes the opened furrow irregular and depth of furrow not uniform, influences the performance of seed and, sometimes, makes them stop working. All these phenomena will influence the seeding quality.

开沟器是播种机、施肥机上的重要部件，在含水量较大的土壤中工作时，土壤粘附在工作表面，改变了表面形状，导致牵引阻力增大，开出的沟形不整齐，使种子在沟中的深度不一致，影响播种质量，严重时使出苗率降低10%，甚至使其无法作业。

In addition,this fluid can prolong the service lives of cutting tools and grinding wheel,enhance their working efficiency,and decrease the surface roughness of the workpiece as well, instead of the traditional saponified oil and emulsion.

它是由防锈剂、抗磨剂、防腐剂和多种表面活性剂复配而成，具有优良的冷却润滑和清洗防锈能力，能延长刀具和砂轮的使用寿命，提高工件表面光洁度和工作效率，可代替传统的皂化油和乳化液。

This paper discusses design and realizable methods of remote test output interface from logical design angle.

本文从逻辑设计的角度讨论遥测输出接口的设计及实现方法。

This also 星体投射plies to buildings, structures and geological features.

这也适用于建筑物和地质特征。