查询词典 working conditions

Inspirited periodically by means of centrifugal inertial force, the lopsided rotor will produce coercionary vibration and inordinate noises, accordingly result in the exacerbating of the working conditions. At the same time, the components of the axletree will wear down quickly, that has reduced the natural life and working efficiency.

由于周期性的离心惯性力对转子的激励作用，不平衡转子将产生强迫振动和过度噪声，从而导致工作环境恶化，加速轴承等零部件的磨损，降低机器的使用寿命和工作效率。

This paper referred to simulating the supersonic double cone inlet" s flow field of ramjet pill assisted range projectiles at a variety of working circumstances, pressure contours, density contours and Mach number contours of inlet" s flow field were given When cone combination, relative location of cone core and cowl lip, the pressure of outlet, inflow Mach number and angle were changed, flow field and performance parameters of inlet can be affected. Simultaneity, productive mechanism and inducing factors of the inlet surge were also discussed. Then the best working conditions and the best model of inlet were obtained.

本文对冲压增程弹丸所用发动机的双锥超声速进气道在各种工况条件下的流场进行了数值模拟，给出了进气道流场的等压线图、等密度线图和等马赫线图，从而观察在不同的锥尖角组合、锥芯与外罩唇口的相对位置、出口反压、来流马赫数和攻角时，对进气道流场及性能参数的影响，并探讨喘振现象的产生机理及诱导因素，以便确定最佳的工作状态，得到最优的进气道模型。

According to the requirement of government regulations, company provides safety working environment and safety working conditions, industrial accident insurance, and essential working protective tools.

按照国家规定，公司提供安全的工作环境和工作条件，依法参加工伤社会保险，提供必要的劳动保护用品。

Under cyclic pressure or torsion load, Four factors with two levels that might influence component stability were assembled into eight performing conditions by orthogonal design. Axial compression micromotion and torsion micromotion were cellected under the eight working conditions.

根据临床上多见的可能对假体微动产生影响的四种因素分设两个水平，采用正交设计方案，组合成8种处理工况对三翼臼进行轴向循环压力载荷测试，同理进行三翼臼的循环扭矩载荷测试。

The article covers the full research on such aspects as mathematic description, numerical analysis method and their practical applications. The diphase heating surface is divided into a hot water section, a evaporation section and a micro overheat section , the problems of model switching are avoided successfully between subcritical and supercritical working condition in the model of The diphase heating surface, and the model can be used for between subcritical and supercritical working condition without causing the model stiff infinity prick up problem. The mathematical model and dynamic characteristic account is unified and predigested for the diphase heating surface of once—through boiler under subcritical and supercritical pressure, and propose that the working conditions at phase change point could be used as divide criterion between water region and steam region under supercritical pressure, the problems are solved successfully between water and steam phase change point under supercritical pressure.

本文在过程的数学描述、数值分析以及实际应用等方面进行了系统的研究分析，将双相受热面统一划分为热水段、蒸发段和微过热段三段，所建立的双相受热面模型不但成功地避免了超临界工况与亚临界工况间的模型切换，而且消除了由区段划分欠妥所引起的模型刚性无限加剧的问题，统一并简化了超临界及亚临界压力下直流锅炉双相区段的数学模型和动态特性计算，而且提出了利用相变点工况作为超临界压力下划分汽水区域的标准，解决了超临界压力下水与蒸汽的相变点问题。

2 Working pressure operatingpressure Working conditions in the steam trap inlet pressure.

3.1.2 工作压力operatingpressure 在工作条件下蒸汽疏水阀进口端的压力。

An example of CODAD system was calculated to study the sum vector of relative amplitude under various firing conditions and working conditions.

结合某船CODAD推进系统实例，对各种发火状态和运行工况下的相对振幅矢量和进行了研究，得出了不同V型夹角情况下扭振激励的主要差异。

Digestion conditions, working conditions of atomic fluorescence spectrometer and conditions of hydride generation reaction were studied. Methods for the reduction from Se to Se by using boiling water bath and UV were compared. The amount of sulfamic acid for the elimination of the interference of nitrogen oxides was also investigated.

探讨了消解条件、原子荧光光度计工作条件及氢化物发生反应条件，对比沸水浴加热和紫外光加热2种将Se还原为Se的方法，研究氨基磺酸消除氮氧化物干扰的最佳条件。

The electromotor is the hard core of the antenna tilting mechanism circuit of the equipment. According to the basic failure rate model and working failure rate model of the national military standards, the electromotor working reliabilities are analyzed under different working conditions and environments.

中文摘要：某装备天线翻倒机构电路的核心部件是电动机，根据国军标中电动机的基本故障率和工作故障率模型，分析了在不同条件和工作环境下电动机的工作可靠性，并对结果做了比较和分析。

Traditional exhaust silencer can not match to the variable working conditions, thus it has difficulty to reduce noise substantially in all working conditions.

传统有源消声器的消声特性，无法随发动机工况变化，因而难以在全工况范围内取得良好的消声效果。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。