查询词典 winding-up

An experimental gear equation of yam winding on usual spinning frame is given out in this paper.

给出了常用细纱机型卷绕成形齿轮的经验计算公式，并以FA506型细纱机为例，对经验公式的推导过程进行了介绍，为棉纺厂工程技术人员进行细纱工艺设计提供了参考依据。

The base fabric has at least one layer assembled by spirally winding a woven fabric strip.

基底织物至少具有一层，由织造的织物带螺旋卷绕组合而成。

The weaving capability of commingled yarns, which include micro-braided yarn, friction spun yarn, winding spun yam and glass fiber yarn was carried out.

研究了由玻璃纤维和丙纶纤维组成的包芯编带纱、摩擦纺纱、空心锭子包缠纱以及玻璃纤维纱的织造性能。

The main types of motor are squirrel -cage,winding and differential types.

主要类型可分为鼠笼式、绕线式及滑差电机拖动。

As an induction motor, it is inevitably for the levitation control winding of bearingless induction motor to induce current in the squirrel cage.

无轴承异步电机作为一种感应电机，其悬浮控制绕组在鼠笼转子中不可避免地感应电流，也就是存在电流损耗。

The rotor winding may be either of two types, the squirrel-cage type or the wound-rotor type.

转子绕组有两种类型：鼠笼型和线绕型。

Pass to count to Wisterch parameter , and the steel wire is different from the molding tool get in touch with the length, and settle the path the research taking the length work the stabber angle to get under differently pull to stir the term, mold core adoption of best severally why size, combine the best work stabber of research the Cape, and settle the path to take the length nextly steel wire is in the molding tool of have fever to measure, air inside dispel-heat calories, winding dispel-heat on the coil-canister , and its molding tool dispel-heat calories of, and cause the steel wire the temperature difference pass in and outing the molding tool to influence steel wire machine function, under the experiment inside pull to stir the term according to the same race different work stabber Cape half of adoption the Cape(7 degree,10 degree,12 degrees, the best mold Cape, experience mold Cape) settle the path to take the length(2-3 mm,3-4 mm,4-5 mms, theories length, experience length) to proceed to experiment, and get the conclusion, work stabber the Cape then is more big the steel wire get in touch with the length with

通过对Wisterch参数，钢丝与模具接触长度、定径带长度、工作锥角度的研究得到了在不同拉拨条件下模芯采用的最佳几何尺寸，并研究最佳工作锥角、定径带长度下钢丝在模具中的发热量、空气中散热量、卷筒上的散热量及其模具散热量的不同，导致钢丝进出模具的温度差别对钢丝机械性能的影响，在实验中根据同种拉拨条件下采用不同工作锥角半角、定径带长度进行试验，得出结论，工作锥角越大则钢丝与模具接触长度越短，钢丝变形越剧烈，在模具中发热量就越高，导致钢丝出模温度高，使钢丝强度、硬度升高，弯曲、扭转次数降低，并且降低模具使用寿命。在其它条件相同的情况下，定径带越长则钢丝与定径带简壁磨擦增大，使钢丝发热量加大，从而使钢丝强度、硬度略升高，弯曲扭转次数略降低但定径带的增大减小了钢丝变形产生的弹性后效使钢丝出模直径比较稳定。

Then can weld starting the resistance directly on the rotor winding, and cancel collecting the electric ring and electric brush.

将定子一种极数的磁场感应于转子绕组中的电流，通过集电环和电刷，但由另一种极数的磁场感应的电流，却自动流经另一闭合回路，而不通过集电环和电刷：于是，如果后一种极数是电动机的工作基波磁场，而把前一种极数作为用以起动的谐波磁场，则可以把起动电阻直接焊接在转子绕组上，而把集电环和电刷取消，从而出现了转子电路上无集电环、无电刷、无触点的谐波起动绕线型感应电动机。

The main body of a book has been set forth mainly take dismantling the old electric motor stater winding as example,simple dismantling method in not different with occasion.

主要以拆除电机定子旧绕组为例，简单阐述了在不同场合采用不同的拆除方法，及时发现电机的异常问题，及时修理，从而提高电机的使用寿命。

Measure the touchable penetration bolt, yoke clamp, steel banding yoke, steel core and winding ring insulation resistance.

a 应测量可接触到的穿芯螺栓，轭铁夹件及绑扎钢带对铁轭，铁芯及绕组压环的绝缘电阻

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。