查询词典 wheel gear

Analyzing the honing principle of spiral bevel gears based on crossing-axis transmission, the mathematical model of the relative sliding speed of the contact point between honing wheel and gear is achieved. It is determined that the pitch cone of honing wheel depends on the number of teeth in the honing wheel and the angle between the common normal of pitch cones and the plane parallel to both gear and honing wheel axes.

分析了基于交错轴传动的珩齿原理，导出珩磨轮与被珩齿轮在啮合点处的相对滑动速度的数学模型，根据该数学模型可以判定珩磨轮的节锥面是由珩磨轮齿数、公法线和与珩磨轮轴线平行的平面夹角所确定。

Analyse the tooth geometry of Klingelnberg Cyclo-Palloid spiral bevel gear.,according to the relative position and kinematic relation of the cutter heads,virtual crown gear and the processed wheel blank,established the system of coordinates of the gear cutting, dedcuced the tooth face equation of the virtual crown gear, according to relations of the gear cutting and space theory of engagement, deduced the tooth face equation of klingelnberg Cyclo-Palloid spiral bevel gear, and drawing the three-dimensional graphs of the virutal crown gear and Klingelnberg Cyclo-Palloid spiral bevel gear according to the design and setting parameters.

根据铣齿加工中刀盘、摇台和轮坯的相对位置和相对运动关系建立了切齿啮合坐标系，由矢量的旋转推导了产形轮齿面方程；根据空间啮合原理和切齿啮合关系推导了被加工齿轮的齿面方程；由设计参数和铣齿调整参数计算得到齿面离散数据，绘制了产形轮和摆线齿锥齿轮的三维齿形。

The place of the innovation of this plan depends on becoming ball gear and dish when form emery wheel undertakes clench the teeth moves, ball gear is not to bypass the upend axis of ball heart turns, circle parallel to turn at crossing the axis of the upend axis of ball heart however, dish the motion of form emery wheel is the translation inside 2 dimension plane.

该方案的创新之处在于当球齿轮和盘形砂轮进行啮合运动时，球齿轮并不是绕过球心的竖直轴转动，而是绕平行于过球心的竖直轴的轴转动，盘形砂轮的运动是在二维平面内的平动。

This paper illustrates the processing art method of the hard gear wheel with big modulus in accordance with the mill wheel machine equipment in our factory and analyzed the big modulus gear wheel .

针对我厂现有磨齿机的设备和对特大模数齿轮参数分析制定出特大模数硬齿轮加工工艺方法。

The obstacle (the altitude of 900 mm) process for both sides of a planetary gear train was analyzed in ADAMAS. It is proved that the physical dimension of the planetary gear train, bodywork center position and attachment coefficient are the key effect factors. The driven moment, velocity and normal pressure sharply increased as each wheel surmounting obstacles, but they were moderate after the front wheel came over the obstacles. Another weaker pulse occurred when the rear wheel began climbing, and then the parameters reached a plateau.

行星轮系的结构尺寸、车体质心位置及附着系数对越障高度影响较大；各轮系越障时出现驱动力矩、速度和正压力急增的现象，前轮系的前轮越上障碍后，各参数值趋于平稳，后轮越障时又出现瞬时脉动，但脉动较小，后轮系也有相同的变化趋势，各轮的阻力矩和输出功率与正压力变化趋势相同。

Traditional worm casting ladle is adopt to the lower light revolving shaft, before pouring, molten iron is self dumping, using self-locking of worm gear, control dumping torque of casting ladle, pouring later, man turn on hand wheel, bevel gear turn to worn gear drive, and turn casting ladle pouring, don't turn on hand wheel, another side of worm gear tooth self-locking, control vertical torque of casting ladle.

传统蜗轮浇包都是采用较低的轻便转轴，浇注前期，铁水自己倾倒，利用蜗轮的自锁性，控制浇包的倾倒力矩；浇注后期，人扳转手轮，伞齿轮转向蜗轮传动，翻转浇包浇注，不扳动手轮时，蜗轮齿的另一侧面自锁，控制浇包的竖直力矩。

The paper summrized lubrication technology and the selection of lubricant for rotary kiln, grate cooler, mill, conveyor mechanical equipment and large scale fan as following,(1)in rotary kiln, apply oil spoon of circulatory lubrication or pump forced oil supply system in the roller supporting mechanism and use (superscript #)680 high load industrial gear oil, and use lubrication method of idle oil wheel or spray in drive gear wheel and select solid lubricant which has high viscosity, strong adsorbability, good abrasion resistance in utmost pressure and lattic crystal structure,(2) in grate cooler, use immersion oil lubrcation in reducer and boiled oil centralized lubrication method in supporting roller and guide roller bearing, choose (superscript #)1 limit pressure lithium lubrcant grease,(3) in mill, use circulatory lubrication with fluxing oil station in drive mechanism and circulatory lubrication with high-low pressure fluxing oil station in main bearing and sliding shoe bearing and select N320 industrial gear oil.

文章全面总结了回转窑、篦冷机、磨机、输送机械及大型风机的润滑技术和润滑剂的选择。其中，(1)回转窑的托轮支承装置一般采用油勺供油的连续循环润滑方式或油泵强制供油系统，润滑油选用680重负荷工业齿轮油；传动大小齿轮的润滑一般采用带油轮或喷雾的润滑方式，润滑剂宜选用粘度高、吸附性强、极压耐磨性好、具有点阵晶体结构的固体润滑剂；(2)篦冷机中传动减速机的润滑一般采用浸油飞溅润滑；托轮，挡轮轴承的润滑一般采用干油集中润滑的方式，润滑脂一般选用锥入度310~340的1极压锂基润滑脂；(3)磨机中传动装置一般采用稀油润滑站循环润滑和冷却的方式；主轴承或滑履轴承的润滑一般采用高低压稀油润滑站循环润滑和冷却的方式，润滑油一般选用N320工业齿轮油。

Changsha, Hunan Tianming Machinery Industrial Co., Ltd. is a transmission gear, rack, chain wheel, crane slewing reducer, coupling, machine tool accessories, dual-metal bushing, pulley, bevel gear, helical gear, charcoal machine, worm gear, non - Standard design and processing, construction of the lift gear, manual steam valve, screw and nut, machine, ring gear, spline shaft and other products Co., Ltd. specializes in processing, the company is headquartered in Changsha, Hunan, Changsha, Hunan Tianming transmission machinery Industrial Co., Ltd. has a complete and scientific quality management system.

湖南长沙天明传动机械实业有限公司是齿轮、齿条、链轮、塔吊回转减速机、联轴器、机床配件、双金属衬套、皮带轮、锥齿轮、螺旋齿轮、木碳机、蜗轮蜗杆、非标设计及加工、施工电梯齿轮、手动汽阀、丝杆及螺母、分切机、内齿轮齿圈、花键传动轴等产品专业生产加工的股份有限公司，公司总部设在湖南长沙，湖南长沙天明传动机械实业有限公司拥有完整、科学的质量管理体系。

There are two worn gear drive device of open-close and turn over on the worm gear blind cut-off valve gate. The gear rim, gear wheel and screw pole screw pairs of open-close worm gear box drive the right and left valve body to clamp and release. The turn-over worm gear box drives the valve disc to open. There is limit block on the valve disc to ensure the open-close position of the valve disc.

蜗轮传动盲板切断阀，阀门中设有启闭和翻转两个蜗轮传动装置，启闭蜗轮箱通过齿圈、齿轮和丝杆螺旋副驱动左、右阀体完成松开、夹紧动作，翻转蜗轮箱驱动阀板完成开启动作，阀板上设有限位挡块以保证阀板的启闭位置。

By each gear wheel system is a fixed geometric axis is divided into a fixed axis and the epicyclic gear train, epicyclic gear train again planetary gear train and differential gear train.

按轮系中各齿轮的几何轴线是否固定分为定轴轮系和周转轮系，周转轮系又有行星轮系和差动轮系。

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。