查询词典 welded

Use some of the newer wires by BHP that are welded after galvanisation.

在这种情况下，当鹦鹉啜咬器皿时就可能会吞下过量的铅或锌。

Firstly, wherever possible avoid cheap wire, as it often has tags and flakes of zinc on it, and contains high levels of lead. Use some of the newer wires by BHP that are welded after galvanisation.

现在有些新产品在金属电镀后再镀上一层 BHP，当然价钱会比较昂贵，但相对比较花费在治疗和药物的金钱就已经值得！

The advantage of this is that thin material can be welded in the spray transfer mode which produces a smooth weld with less spatter than the short circuiting mode.

这样的好处是，可在喷射过渡方式下焊接薄材料，能产生比短路过渡飞溅少的平整焊缝。

Experiment results show that though the grains of the heat-affected zone are seriously coarsened due to the effect of welding thermal cycle, there is no softened zone and the strength of the welded joint doesn′t decrease because the transformed microstructure is different from the original one.

结果表明：经过焊接热循环的作用，虽然热影响区的晶粒明显粗化，但由于所获得的二次组织形态与钢筋原始组织不同，热影响区未发生软化，也不存在焊接接头强度下降的问题。

Experiment results show that though the grains of the heat-affected zone were seriously coarsened due to the effect of welding thermal cycle, there is no softened zone and the strength of the welded joint doesn't decrease because the transformed microstructure is different from the original microstructure of the rebar.

结果表明：经过焊接热循环的作用，虽然热影响区晶粒明显粗化，但由于所获得的二次组织形态与钢筋原始组织不同，热影响区不发生软化，也不存在焊接接头强度下降问题。

The influence of induction heating for PCD compacts determines the quality of the welded tools.

感应加热过程对聚晶金刚石复合片的影响，决定了焊后刀具的质量。

There is no crewed in or welded cage.

没有螺丝或者焊接架。

I bent the grates and welded the first bar in place to hold them.

i ，搞炉排和焊接第一大律师公会在地方举行。

The author innovated forging process of shell of forging - welded hydrogenating reactor which was awarded The First Prize state Science and Technology Development before, by using VE principle.

运用价值工程原理，改进了获国家科技进步一等奖的锻焊结构加氢反应器的简节锻造工艺，创新后的简节锻造工艺又应用在其他两台类似的加氢反应器上，总计降低生产成本1700余万元

This welding wire not only has the inherent properties of metal powder-cored wire, such as with better welding quality, without slag, highly efficiency and conveniently adjusting the alloying elements etc., but also has the advantage of low hardness in as-welded (less than HRC45), good machinability, high hardness in as-aged (more than HRC55) and better wear resistance with customary working procedure on making or repairing equipments such as rollers when reasonable designing the alloys content. The author adequately makes use of the high-tempering in the required stress relieving working procedure. During this working procedure, which causes the hardness of overlaying metal increased by the reason of austenite changes into tempered martensite and more chiefly what is the precipitation of a lot of carbide by secondary hardening simultaneously. This wire can solve the hard rolled problems of some solid wires with higher alloys while it can get over the conflict of existing overlaying materials what are always possesed high hardness with poor machinability or low hardness, good machinability with poor wear resistance. Further, it also can overcome the intenerating phenomena between welding beads and make the external hardness of overlaying metal uniform. Be sure it could be found important meaning in the overlaying of wear-resistant equipments, such as the precise roller.

该焊丝除了具有金属粉型药芯焊丝焊接质量好、无渣、高效率和合金成分可方便调节等固有的优点外，合理的设计粉芯中的合金成分，按通常工序制造与修复轧辊等设备，充分利用必需的消除应力工序的高温回火，堆焊层金属在奥氏体转变为回火马氏体的同时更主要是通过二次硬化析出了大量碳化物导致硬度增加，使得该焊丝还具有焊态硬度低(小于HRC45)、机加工性能好和时效态硬度高(大于HRC55)、耐磨性能好等优点，解决了某些高合金实芯焊丝轧制困难的问题，同时克服了现行堆焊材料硬度高、加工性能差或者硬度低、加工性能好、耐磨性差的矛盾，并能克服焊道之间的软化现象，使堆焊表面硬度较为均匀，对耐磨件，譬如精轧辊的堆焊具有重要意义。

You can do some assertiveness training.

你可以进行一些自信训练。

We were well on the path to making a rear-wheel-drive global platform," says Mays."

我们正致力于建立一个后轮驱动的平台，"Mays这样说道。"