查询词典 welded

In this method, drill the double holes in the two sides of the point to be determined in welded joints, load material bridge by an indentor until it is broken, record the response between applied load and indentor displacement. We can call this method as double holes microshear test.

在被测材料的小区域两侧开两小孔，剪切刀具从其中一孔对被测区域的材料加载直到破坏，记录加载过程中的载荷位移曲线。

The results showed that counterweight had been welded wrongly in inwall of roll cylinder,the microstructure of roll cylinded,mechanical property and stress state had been changed.

结果表明，由于错误地将平衡重焊在了辊筒内壁，由此造成辊筒的显微组织和力学性能以及受力状况发生了变化。

At the same time, is also the stainless steel industry earlier through ISO9001 (2000) international quality system certification of enterprises, with advanced equipment, scientific management and operation of a very modern concept, products awarded as "China Famous" designation, and the Ministry of Construction in China Building Decoration Association of Architectural Ironmongery identified by the Commission as "project selected products", all products comply with CJ; T 151-2001 "thin-walled stainless steel pipes" GB12771 "fluid steel pipe welded stainless steel" GB; T 18705-2002 "decorative soldering Stainless Steel Pipe ", GB; T19228.2-2003" stainless steel compression-type pipe fittings to connect with thin-walled stainless steel tube "and other standards.

同时，也是不锈钢行业较早通过ISO9001（2000）国际质量体系认证的企业，凭着先进的设备、科学的管理和极具现代化的经营理念，产品荣获《中国名优产品》称号，并被建设部中国建筑装饰协会建筑五金委员会确认为"工程建设选用产品"，所有产品符合CJ；T 151—2001《薄壁不锈钢水管》 GB12771《流体输送用不锈钢焊接钢管》GB；T 18705-2002《装饰用焊接不锈钢管》、GB；T19228.2—2003《不锈钢卡压式管件连接用薄壁不锈钢管》等标准要求。

This improvement mainly reflected along the rolling direction, so that steel is no longer a certain extent, isotropic body; pouring the bubble was formed, cracks and loose, but also under high temperature and pressure have been welded together.

这种改善主要反映了沿轧制方向，使钢不再是在一定程度上，各向同性体；浇注泡沫形成，裂缝和松动，但在高温高压也被焊接在一起。

Door jamb can be constructed of heavy steel tube frame for welded

为焊接屏蔽室构造的重钢门框结构，标准模块式屏式

In addition, longitudinal or transverse residual stress distribution of welded joint can be improved by using of trailing peening.

此外，焊接接头的纵向及横向残余应力分布状态均有了很大程度的改观，应力水平相对较低，有利于焊接结构的尺寸稳定。

And welded rail s have begun to replace jointed rail .

焊接轨道已开始代替有接头的轨道。

The results showed that the fracture toughness of the weld of HFW pipe was lowest.The value of absorbed energy of HFW weld was closely related to the heat treatment process.But the fracture toughness of fusion zone of submerged-arc welded jointer,its microstructure was coarse granular bainite,and was lower than the other locations of heat affected zone;and with the increasing of steel strength,the effect of welding heat cycles on the pipeline steel became stronger,and form coarse microstructure in fusion zone leading to decrease fracture toughness.

结果表明，高钢级管线钢高频焊接焊缝处的断裂韧性最低，其冲击功大小与热处理工艺密切相关；而埋弧焊接热影响区断裂韧性在熔合线处最低，其主要原因是此处的组织为粗大的粒状贝氏体，而且强度越高焊接热循环对管线钢的作用越强，在熔合线附近更容易产生粗大组织，使断裂韧性降低。

Using metallographic analysis, original structure and surface deficiency were obtained, the influence of the structure on corrosion speed was settled, the surface macrography patterns of welded joint in different temperature and concentration were got. Microscopic patterns after corrosion in different condition were gained by SEM, though which the influence of temperature, concentration and structure on corrosion was easily observed.

采用金相分析法，不仅获得了腐蚀前焊接接头的原始金相组织以及表面缺陷，确定了组织及缺陷对腐蚀速率的影响，而且得到了焊接接头在不同温度、浓度条件下腐蚀后的宏观形貌，采用场发射扫描电子显微镜得到了焊接接头在不同条件下腐蚀后的微观形貌，从而直观地得到了温度、浓度以及组织对焊接接头腐蚀速率的影响。

The macrostructure of the friction welded joint and the microstructure of welding area was examined and analyzed, it was found that the simulation results agree well with the experimental results.

对接头的宏观形貌和焊缝区的微观组织进行观察分析，发现模拟结果与实验结果吻合较好。

Lugalbanda was a god and shepherd king of Uruk where he was worshipped for over a thousand years.

Lugalbanda 是神和被崇拜了一千年多 Uruk古埃及喜克索王朝国王。

I am coming just now,' and went on perfuming himself with Hunut, then he came and sat.

我来只是现在，'歼灭战perfuming自己与胡努特，那麼，他来到和SAT 。