英语人>网络例句>weld seam 相关的网络例句
weld seam相关的网络例句

查询词典 weld seam

与 weld seam 相关的网络例句 [注:此内容来源于网络,仅供参考]

Axis X of the frame is defined as seam axis, axis Z is defined as bisector of included angle, and axis Z is the axis of weld gun in the simulating environment.

将焊缝特征坐标系的X轴作为焊缝的轴线,将Z轴作为焊缝的中心线,Z轴即为仿真环境下的焊枪的轴线。

Apart from the speed of arithmetic that is used to process the image get from CCD and get the value to control torch, it is, too, very important for weld qualification of seam-tracking system based on CCD that how to make the whole systems structure brief and its running efficiency.

除了算法的影响外,在基於视觉信息的高速实时焊缝跟踪系统中,如何把整个系统设计得简炼、紧凑,使之能够高效运行,也是提高整个系统速度的一个重要的因素。

The residual stress distribution of the tangential residual stress,the hoop residual stress and the normal residual stress test of spiral seam arc weld pipe were studied on the basis of elastic mechanics analysis and superposition theorem.

基于弹性力学应力分析和叠加原理,研究了螺旋缝埋弧焊管切环法残余应力测试中的残余应力分布。

When the Al-Mg-Zr-Sc welding wire was used as filling material, the grains of welding seam were refined obviously, and the weld joint was greatly strengthened by forming of fine equiaxial grains layer in fusion zone.

结果表明:采用两种焊丝焊接的Al-Mg-Sc合金薄板的焊接接头强度系数均大于0.9。

When the Al-Mg-Zr-Sc welding wire was used as filling material,the grains of welding seam were refined obviously,and the weld joint was greatly strengthened by forming of fine equiaxial grains layer in fusion zone .

但采用Al-Mg-Zr-Sc合金焊丝为填充材料时,焊缝晶粒组织明显细化,熔合区形成的细小等轴晶层提高了基材与焊缝填充材料的结合力,焊接接头的屈服强度比采用Al-Mg-Zr合金焊丝为填充材料时提高了100 MPa,显著提高了Al-Mg-Sc合金焊接构件的许用强度,因此焊接Al-Mg-Sc板材更宜采用Al-Mg-Sc-Zr焊丝。

Because of having surplus weld reinforcement height and irregular seam form as well as the influences of polyethylene raw materials and coating process, the quality problems of ununiformity in thickness of 3PE coating and coating thickness reduction on helical seam occur.

由于螺旋埋弧焊管存在焊缝余高超高和焊缝形貌不规整等现象,加之聚乙烯原材料及涂敷工艺等因素的影响,会使三层PE防腐涂层出现涂层厚度不均、焊缝处涂层减薄等质量问题。

Seam welded C276 alloy heat exchanger tubing to UNS N10276 is allowed providing the tube weld is not peened or bead worked, but the whole tube in both weld and base metal is cold drawn, bright annealed and passivated and is to ASTM B626 Class III specification.

如果管子焊缝不是peened or bead worked,则使用焊缝缝焊接式C276合金换热管(UNS N10276)是允许的,但是焊缝和基金属上的整个管子是冷拔的、光亮退火和钝化的,并应符合规范ASTM B626 Class III上的规定。

The use of thin seam annealing furnace hoop-shaped composite structure, in large containers, weld any combination, dismantling, and transportation convenience, temperature uniformity, excellent insulation effect, heat losses small, can really achieve the elimination of welding seam annealing stress effect.

该焊缝退火炉采用薄箍形组合结构,可在大型容器的焊缝处任意组合,拆卸、运输方便,温度均匀,保温效果极佳,热损失小,真正能够达到焊缝退火消除焊接应力的效果。

Hongye Machinery Factory production of machinery and equipment are widely used in metal processing production: Qi mouth edge, flat crimping, both inside and outside vertical crimping, pressure Blankholder bones, stretch forming, anti-side, crossed, metal ring inside the edge volume, Hemming, sand at the end, both inside and outside the sanding, the appearance of Belt Line, both inside and outside the skin polished, red-shaped punching, vol cylindrical, straight seam welding, weld line pressure, girth welding, pressure ring weld, sheet metal coated oil, pressure spiral teeth, cars spiral teeth.

鸿业机械厂生产的机械设备广泛用于五金制品加工生产:齐口切边、平面卷边、垂直内外卷边、压边压骨、拉形、反边、划线、金属圈卷内边、包边、砂底、内外砂光、外表砂带线、内外去皮抛光、冲形冲孔、卷圆筒、直缝焊、压直线焊缝、环缝焊、压环形焊缝、金属片涂油等、压螺旋牙、车螺旋牙。

The definition of weld slope and weld rotation are described, and characteristics coordinates frame of seam are set up.

给出了焊缝倾角和焊缝转角的广义定义,提出建立焊缝特征坐标系的方法。

第5/7页 首页 < 1 2 3 4 5 6 7 > 尾页
推荐网络例句

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发,分析对称连杆曲线上鲍尔点的产生条件,提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品,年生产总值3000万美元,产品价廉物美、选料上乘、质量保证,深受国内外客户的青睐

The eˉtiology of hemospermia is complicate,but almost of hemospermia are benign.

血精的原因很,以良性病变为主。