英语人>网络例句>weld joint 相关的网络例句
weld joint相关的网络例句

查询词典 weld joint

与 weld joint 相关的网络例句 [注:此内容来源于网络,仅供参考]

The main projects of strip-slitting factory: edge slitting, end slitting, butt weld, coil joint, etc. The scale of specification: thickness 0.6-3mm, width 50-520mm. The products are mainly exported to South Korea, Southeast Asian countries and middle-east area etc.

带钢纵剪加工项目主要包括:切边、切头尾、对焊、并盘等,纵剪加工后成品规格范围主要是:厚度0.6mm -3mm ,宽度50mm -520mm ,其纵剪加工产品以出口为主,销往韩国、东南亚国家和中东地区等。

The results show that mechanical heterogeneity has great influence on the J-integral of welded joint containing transverse crack. The J-integral on the path cross the interface between welded joint and base metal is higher than the J-integral on the paths in the weld metal for undermatched joint,while the J-integral on the path cross the interface between weld metal and base metal is lower than the J-integral on the paths in the weld metal for overmatched joint. Moreover,the difference of J-integral values increases with the increasing of the load and strength mismatching difference and the path-enclosed length of interface between weld metal and base metal.

计算结果表明:力学不均匀性对含横向裂纹焊接接头的J积分有重要影响,低匹配焊接接头中积分路径穿越焊缝与母材界面的J积分值高于积分路径在焊缝内的J积分值,高匹配焊接接头中积分路径穿越焊缝与母材界面的J积分值低于积分路径在焊缝内的J积分值;载荷越大,焊缝与母材的强度差别越大;积分路径中包含的焊缝与母材界面长度越大,J积分的差值越大。

Thirdly, with the modified Gurson model of the MARC finite element method soft, the damage behave of the welded joint was simulated. It was found that in the undermatched welded joint, the damage mainly happened in the soft weld line and with the decrease of the weld line抯 width, the damage抯 development was faster. As for the overmatched welded joint, the results showed that the damage mainly happened in the soft base metal and with the increase of the weld line抯 width, the damage抯 development was faster. While the width of the weld line was narrower than three millimeters, the high strength weld line could improve the anti-damage capability of the overmatched welded joint.

通过计算发现在低匹配的焊接接头中,损伤主要发生在低强度的焊缝中,并且焊缝宽度越小,焊接接头的损伤就越严重;而在高匹配的焊接接头中,损伤主要发生在紧临焊缝的强度较低的母材上,随高强度焊缝宽度的增加,焊接接头的损伤发展程度加剧,当焊缝宽度小于3mm时,高强度焊缝的加入对焊接接头能起一个强化的作用,提高了焊接接头的抗损伤能力。

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝,在焊缝两端设引弧板和引出板,必须在引弧板上引出后再焊到焊缝区,中途接头则应在焊缝接头前方15~20㎜处打火引弧,将焊件预热后再将焊条退回到焊缝起始处,把熔池填满到要求的厚度后,方可向前施焊;焊接速度:要求等速焊接,保证焊缝厚度、宽度均匀一致,从面罩内看熔池中铁水与熔渣保持等距离(2~3㎜)为宜;焊接电弧长度:根据焊条型号不同而确定,一般要求电弧长度稳定不变,酸性焊条一般为3~4㎜,碱性焊条一般为2~3㎜为宜;焊接角度:根据两焊件的厚度确定,焊接角度有两个方面,一是焊条与焊接前进方向的夹角为60~75 ;二是焊条与焊接左右夹角有两种情况,当焊件厚度相等时,焊件与焊件夹角为45 ;当焊件厚度不等时,焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角;收弧:每条焊缝焊到末尾,应将弧坑填满后,往焊接方向相反的方向带弧,使弧坑甩在焊道貌岸然里边,以防弧坑咬肉。

The suitability of the different processes was analyzed by observing the weld appearance,studying the microstructure and measuring the mechanical properties of the joint.The results show that a favorable weld can be obtained under the suitable parameters by laser beam welding or tungsten inert gas welding with filler metal.The TIG welded joint has a wider HAZ,and the laser welde...

试验结果表明:在工艺参数合适的条件下,加焊丝TIG焊和激光焊均能获得成形较好的焊接接头;TIG焊接头热影响区较宽,焊缝深宽比小,而激光焊时热影响区不明显,焊缝深宽比大;两种焊接方法所获得的焊缝区组织均为均匀的等轴晶,但激光焊时焊缝组织更细,从而使接头抗拉强度大幅度提高,达到母材的94%左右。

The results show that the main cause of the angular distortion of the lap joint is the non-uniform distributed inherent shear strain component that is vertical to the weld line and exists in the plane paralleling to the weld line.

结果表明:搭接接头焊接角变形的产生主要是由焊缝及其附近区域与焊缝平行的平面内垂直于焊缝方向上不均匀分布的固有剪切应变分量引起的。

The research results indicate that the interface between weld and l2Crl MoV steel is the weakest part of welded joint. However ,the interfacial failure tendency of low match welded joint is less than those of medium and high match welded joint.

试验结果表明,焊前预热250℃,焊后回火750℃×1h,加速模拟运行500h后,高匹配和中匹配接头的力学性能劣化明显,界面蠕变损伤及失效倾向较大;而低匹配接头的力学性能优于高匹配和中匹配接头,界面蠕变损伤较轻,失效倾向较小。

In practical application item, UIC515 Code is firstly applied for analyzing the complete welded frame by finite element method to get the area with bigger nominal stress and lower fatigue behavior, and then study the hot spot stress fatigue strength evaluation approach of the typical fillet ring joint at the connection of tubular transom and side frame, the plate to plate end weld between side frame web plate and anti-yaw damper hold and the non-close ring end weld at the connection of braking unit hold and tubular transom.

在热点应力疲劳评估时,首先对焊接构架中的环向角焊缝、板间端焊缝以及非闭合环向端焊缝进行简化,得出了相应的几何应力集中系数和热点应力疲劳极限,为热点应力疲劳评估提供了依据。

Aiming at the engineering problem that K welding machine is used to weld PD3 60kg/m rail during welding production at present, the quality of the joint falls short of the standard of TB/T1632-91 because of the objection of grey-spots in the welding joint, this paper analyses the element which influence the welding joint quality in detail from the stability of flash of the accelerating step of the rail, finds out the relationship between the stability of flash-butt welding and the quality of rail joint, provides the measure for controlling the quality of rail welding and some gist for establishing perfect controlling system of welding joint quality

针对目前焊轨生产中采用K型焊机焊接PD3 60kg/m钢轨,接头灰斑缺陷多,性能难以达到部颁标准要求的工程问题,对材质、焊接电压、焊接工艺对接头质量的影响进行研究,并从钢轨焊接加速烧化阶段的闪光稳定性入手,详细分析了影响接头质量的因素,找出了钢轨闪光焊稳定性与质量的关系,提出了控制钢轨焊接质量的措施,为建立完善的焊接质量控制体系提供了依据。

The results obtained from finite analyses indicate, under assured weld quality, the effect of ratio of axial compression stress to strength is relative better to moment-resistant bearing capacity of column joint, the ratio of axial compression stress to strength is bigger, the moment-resistant bearing capacity of column joint is bigger, earthquake resistant capacity is better

结果分析表明:在保证焊接质量的前提下,轴压比对节点柱的抗弯承载力影响较大,轴压比越大,抗弯承载力越大,节点的抗震性能越好。

第3/5页 首页 < 1 2 3 4 5 > 尾页
推荐网络例句

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发,分析对称连杆曲线上鲍尔点的产生条件,提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品,年生产总值3000万美元,产品价廉物美、选料上乘、质量保证,深受国内外客户的青睐

The eˉtiology of hemospermia is complicate,but almost of hemospermia are benign.

血精的原因很,以良性病变为主。