查询词典 wedge-shaped

To obtain both construction security and the feasibility in tunnel engineering, and to understand the contact mechanism in these complex cutting cases, this numerical approach simplifies normal wedge cutter indented into intact rock for simulating the process of fragmentation using a two-dimensional tool of distinct element method, so-named PFC2D.

故本研究以分离元素法之二维数值软体PFC2D为本；进行模拟楔形刃口正向贯入岩材之接触破坏行为，以数值耦合（PFC2D＆FLAC）之方式，先就单压及巴西试验作校验，再应用於贯切破坏之模拟，并比对贯切行为之理论模式与相关实验数据，俾能提供隧道工程与地下管道机械开挖之安全性与施工效率探讨之佐证。

The effect of the configuration parameters of sub slot, the distribution of winding's cooling ducts, and the diameter of slot wedge on mass flow rate distribution in radius ducts was presented.

研究副槽结构、转子槽楔出风口直径、转子径向风道布置等对转子径向风道流量分配的影响。

To obtain more uniform temperature distribution and relative lowest temperature over cross section of the rotor, on the basis of test data of a given example of a 150MW turbo generator with air coolant, numerical solution of two dimensional modelling equations of air turbulent flow and heat transfer in and between cooling duct and rotor were carried by the Finite Volume Method at condition of varying configuration parameters of sub slot, the number of winding's cooling ducts and center distance of them, and the diameter of slot wedge.

为了能够得到转子截面较均匀并且最高温度值较低的优化温度分布，文中在150MW空冷汽轮发电机转子实验研究基础上，改变副槽的几何形状、径向通风沟的条数及间距、槽楔出风口直径等几何量，采用有限体积法求解转子本体及通风道内空气的传热及紊流流动等二维离散方程组。

In the rotor winding ventilation system with sub-slot, the configuration parameters of sub slot, the distribution of winding's cooling ducts, and the diameter of slot wedge directly affect the flow characteristics of coolant in cooling ducts.

在转子副槽通风冷却系统中，副槽结构、径向风道分布、槽楔出风口直径等参数，直接影响转子风道冷却介质流动特性。

Wedge joint is used for fixing the head of wire rope sling.

楔形街头是钢丝绳索具的一种索头固定形式。

Hydraulic pressed machine, hydraulic insertion machine, horizontal testing machine, textile lifting sling, open wedge socket, shackle, wire rope sling, lifting chain.

8F31 钢丝绳压套机，钢丝绳插套机，拉力实验机，吊装带，楔型接头，卸扣，钢丝绳索具，起重链条。

The float plate block and slide block are controlled by the two-way wedge and located by the ringer.

该模具的凹模由固定部分和活动部分组成，浮动凹模镶块和滑块部分由双向斜楔控制、套环定位，保证了横向和纵向压料的精度，满足了零件质量要求。

A flat washer may be inserted between the screw and the wedge test plate to eliminate the effects of torque robbing features.

可以在螺栓和楔形垫圈之间装入一个平垫圈来消除由于楔形垫圈而产生扭矩削弱的影响。

This paper presents the Machining Tool geometry of the former flank, the main flank, flank, the main cutting edge, Under the cutting edge tip cutting plane, the main section, the former Kok, horn, wedge angle edge angle, pointed knife, the blade angle, vice horn, Under the Frontier concept, the concept of cutting consumption, and the general circumstances of their choice method for processing slender shaft. cast iron materials, aluminum, stainless steel, rubber materials, plexiglass material, cloth bakelite materials, high temperature alloys, aluminum-magnesium alloy, hardened steel, the typical trapezoidal thread, the thread Triangle, Speaking at the trapezoidal screw thread pitch of the Tool geometry of the selection methods and cutting the amount of cutting fluids reasonable choice.

本文介绍了在机械加工中车刀几何角度中的前刀面、主后刀面、后刀面、主切削刃、副切削刃刀尖切削平面、主截面、前角、后角、楔角主偏角、刀尖角、刃倾角、副后角、副前角的概念、切削用量的概念、以及一般情况下的它们的选择方法，进行加工细长轴、铸铁材料、铝合金、不锈钢、橡胶材料、有机玻璃材料、夹布胶木材料、高温合金、铝镁合金、淬火钢、典型梯形螺纹、三角螺纹、特在螺距的梯形螺纹等的车刀几何角度的选取方法切削用量及切削液的合理选择。

An integrated unit of ball screw stripping,ball bearing tapered wedge and fixed-distance pull off was adopted in the design of injection mould for screw plug.

在螺塞注射模具设计中，采用了滚珠丝杠脱模装置和滚珠、斜楔拉模、定距联合装置，利用滚珠、螺母、丝杠及齿轮传动自动拧出螺纹塑件，实现塑件自动脱模；利用滚珠、斜楔、滑块机构拉开定模板和浇口板并控制其拉开距离，从而达到自动生产目的。

We have no common name for a mime of Sophron or Xenarchus and a Socratic Conversation; and we should still be without one even if the imitation in the two instances were in trimeters or elegiacs or some other kind of verse--though it is the way with people to tack on 'poet' to the name of a metre, and talk of elegiac-poets and epic-poets, thinking that they call them poets not by reason of the imitative nature of their work, but indiscriminately by reason of the metre they write in.

索夫农 、森那库斯和苏格拉底式的对话采用的模仿没有一个公共的名称；三音步诗、挽歌体或其他类型的诗的模仿也没有——人们把&诗人&这一名词和格律名称结合到一起，称之为挽歌体诗人或者史诗诗人，他们被称为诗人，似乎只是因为遵守格律写作，而非他们作品的模仿本质。

The relationship between communicative competence and grammar teaching should be that of the ends and the means.

交际能力和语法的关系应该是目标与途径的关系。