查询词典 wear

Under the condition of two bodies abrasive wear, the wear resistance of the wear resistant composite with the bionic unsmoothed surface is 29 times as much as that of 45 steel.

仿生非光滑耐磨复合层具有很高的韧性和塑性，且可根据需要调节复合层的厚度，为提高地面触土机械部件的抗磨性开辟一条新的途径

This research applied austempering heat treatment to obtain various microstructures in the matrix of ductile iron and studied their erosion wear behavior. The effects of different impact angle and microstructure on erosion wear rate and morphology wase investigated. Mechanical property evaluation together with SEM analysis was also carried out to correlate the wear behavior observed.

本研究系以球墨铸铁进行沃斯回火热处理，获得不同基地组织的试片，再利用冲蚀磨耗实验来进行各种角度的冲蚀磨耗，配合机械性质测试及扫描式电子显微镜来观察冲蚀表面，探讨沃斯回火热处理对球墨铸铁不同冲蚀磨耗型态与冲击角度的影响。

This welding wire not only has the inherent properties of metal powder-cored wire, such as with better welding quality, without slag, highly efficiency and conveniently adjusting the alloying elements etc., but also has the advantage of low hardness in as-welded (less than HRC45), good machinability, high hardness in as-aged (more than HRC55) and better wear resistance with customary working procedure on making or repairing equipments such as rollers when reasonable designing the alloys content. The author adequately makes use of the high-tempering in the required stress relieving working procedure. During this working procedure, which causes the hardness of overlaying metal increased by the reason of austenite changes into tempered martensite and more chiefly what is the precipitation of a lot of carbide by secondary hardening simultaneously. This wire can solve the hard rolled problems of some solid wires with higher alloys while it can get over the conflict of existing overlaying materials what are always possesed high hardness with poor machinability or low hardness, good machinability with poor wear resistance. Further, it also can overcome the intenerating phenomena between welding beads and make the external hardness of overlaying metal uniform. Be sure it could be found important meaning in the overlaying of wear-resistant equipments, such as the precise roller.

该焊丝除了具有金属粉型药芯焊丝焊接质量好、无渣、高效率和合金成分可方便调节等固有的优点外，合理的设计粉芯中的合金成分，按通常工序制造与修复轧辊等设备，充分利用必需的消除应力工序的高温回火，堆焊层金属在奥氏体转变为回火马氏体的同时更主要是通过二次硬化析出了大量碳化物导致硬度增加，使得该焊丝还具有焊态硬度低(小于HRC45)、机加工性能好和时效态硬度高(大于HRC55)、耐磨性能好等优点，解决了某些高合金实芯焊丝轧制困难的问题，同时克服了现行堆焊材料硬度高、加工性能差或者硬度低、加工性能好、耐磨性差的矛盾，并能克服焊道之间的软化现象，使堆焊表面硬度较为均匀，对耐磨件，譬如精轧辊的堆焊具有重要意义。

The analysis of leakage causes for flash trough was presented, and the wear layers on inlet tube and the baffle wear plate inside of flash trough were used to increase the wear life of flash trough.

分析了闪蒸槽泄漏的原因，采用在进口接管堆焊耐磨层及筒体上增加耐磨档板的方法对闪蒸槽进行了改造，增加了闪蒸槽的寿命。

The service conditions of two wear fits, rocker seat to base portion and plate member to adapter, are very strict. The two wear fits meet strength requirements and prevent themselves from deterioration due to excess wear and contact fatigue.

其中摇动台与其支承座、摆块与承载鞍两对摩擦副服役条件苛刻，要求具有一定强度，同时又能抗磨损和接触疲劳破坏。

The effect of nano-diamond powder on the forming speed, microhardness and wear-resistance of compound brush plating Ni-P coating, the wear-resistance of brush plating Ni-P coating, Ni-P nano-diamond composite coating and Ni-P micro-diamond composite coating was tested. The mechanism of improving wear-resistance by of composite coating was analyzed.

中文摘要：研究了纳米金刚石粉对复合电刷镀镀层形成速率、显微硬度和耐磨性的影响；测试了在不同的热处理温度、载荷及金刚石粉含量下复合刷镀层的耐磨性能；分析了复合镀层的磨损机理。

That time of he, wear skull cap, wear square jacket, crest red 缨 plait, wear a pair of faces shoe, the 踱 wears to tread everywhere, coming in and going out north big campus, speaking British poem greatly on the classroom of boudoir, it ising said is one viewing in the then capital city.

那时的他，戴瓜皮帽，穿方马褂，顶红缨辫，穿双脸鞋，踱着四方步，出入北大校园，在红楼的课堂上，大讲英国诗，据说是当时的京城一景。

Both ends of the wear cap maintenance: Gear pump with cast iron end caps, wear phenomenon occurs after a slight revision in the plate mill level, more serious wear and tear on the grinding surface grinding machine should be revised in the flat.

两端盖的磨损维修：齿轮泵的端盖用铸铁制造，出现磨损现象后，轻微的可在平板上研磨修平，磨损比较严重时应在平面磨床上磨削修平。

Gentlemen wear the swallowtail with bow-tie, or wear the black tailored suit. Ladies wear the dress styled suit or dinner coat.

男士所穿的多为配以蝴蝶结的的燕尾服，或是黑色西装套装；女士所穿的则多为连衣裙式的单色大礼服或小礼服。

It is considered that link wear speed on seal surface is proportional to the contacting pressure. The impacting of valve disk on valve seat is the important reason of abrasive wear, and the relative motion of disk is a main reason for errosion wear of pump valve. The cycles per minute is an important factor to influence the valve motion and the impact force.

结果表明，泵阀密封面联接磨损的磨损速度与密封面上的接触比压成正比，泵的冲次是影响阀盘运动规律及对阀座产生冲击的重要因素，泵阀产生磨粒磨损和疲劳磨损的主要原因是泥浆、阀盘和阀座的冲击，冲蚀磨损导致泵阀的刺蚀。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。