查询词典 wear

Since the rotary plunger pump piston at each stroke can randomly rotate constantly change with the pump plunger cylinder contact surface, so that circular plunger gradually wear uniform or scaling at the same time, sand from the plunger and pump barrel between discharge and resolved accumulation Materials abrasion caused by wear and serious positioning rod release.

自旋转柱塞抽油泵可以使柱塞在每冲程中随机转一下，不停地转变柱塞与泵筒的接触面，使柱塞圆周逐渐匀称磨耗的同时将砂粒或结垢从柱塞与泵筒之间排出，解决了磨蚀材料聚集所导致的紧张定位磨耗及杆柱脱扣。

This paper analyzed the relations between vibration and plunger wear of reciprocating pump , and studied the characteristics for the diagnosis of plunger wear.

分析了往复泵柱塞-缸套磨损振动诊断机理，研究了振动时域、频域特征。

My necklaces are all of FAMOUSSTONE, so I don't wear, just don't wear.

我的项链都是石头记的，我不戴我就是不戴。

And the strengthening mechanism can be described as follows: WC cemented carbides have interlaced short-clubbed grain, and in the bend strength test, the microcrack generates at WC/WC grain boundary, and may be blocked by interlaced fine-clubbed grains during extending, which induce the intergranular pulling-out. Due to the pulling-out mechanism, fracture-extend energy is greatly expended, thus bend strength is increased. The wear mechanism is groove wear and spalling of WC grains.

热机械合金化合成的WC-Co硬质合金比传统方法制备的同类WC合金具有更高的强度，其机理是：热机械合金化合成的WC合金具有交替排列的短棒状组织，在三点弯曲试验中，微裂纹萌生于WC/WC晶界位置，受到交错排列的短棒状晶粒的阻碍，裂纹扩展以短棒状晶粒的拔出方式进行，极大地消耗了裂纹扩展的能量，从而提高了弯曲强度；合成试样的摩擦磨损过程以犁沟磨损和WC颗粒的剥落为主要特征。

At present, the location of the anti-lopsided wear centralizer used in fields is mainly based on the deviation angle. In fact, lopsided wear may be caused by the change of azimuth angle or by the vertical well section and hold angle section during the working of the bucket rod.

目前油田矿场主要根据井斜角来确定防偏磨扶正器下入位置，实际上方位角变化也能导致偏磨，抽油杆杆柱在运动过程中直井段和稳斜段也会产生偏磨。

Locator, also known as wheel gear wheel organ, backup pad, block positioner, stop etc., is high intensity of natural rubber vulcanized high pressure synthesis, compression performance, and the slope has some flexibility, black and yellow with reflective material compliance with international standards, clearly visible and has slow down, non-slip, wear, reduce tire wear and so on.

定位器又称车轮挡轮器、倒车垫、阻位器、挡车器等，是采用高强度天然橡胶经硫化高压合成，抗压性能好，而且坡体有一定柔软度，黑黄相间含反光材料符合国际标准，醒目明显并具有减速、防滑、耐磨、减轻对车辆轮胎的磨损等特点。

Theoretically the pump blade failure mechanism was worn on, the impact of wear failure leaves the various factors was analyzed, combined with practice pumping station operation and maintenance experience, the focus at a reasonable selection, surface heat treatment, non-metallic protective coating alloy powder spray repair welding and welding six aspects, premature wear of the pump blade technical measures and repair methods was prevented in order to enhance its effective life.

理论上阐述了水泵叶片磨损失效的机制，具体分析了影响叶片磨损失效的各种因素，并结合泵站运行实践和维修经验，重点在合理选材、表面热处理、非金属涂层防护、合金粉末喷焊和补焊等6个方面，提出了防止水泵叶片过早磨损的技术措施和修补方法，以提高其有效的使用寿命。

The Company QG chromium carbide hardfacing composite plate, using welding or brazing with metals produced by automatic arc welding alloy powder to add new process methods, the formation of hypereutectic high chromium multi-element alloys superhard wear-resistant layer, can significantly improve easy to wear pieces of equipment and steel production life.

本公司QG碳化铬耐磨堆焊复合钢板，采用焊丝或焊带产生的金属电弧添加粉末合金自动堆焊新工艺方法，形成过共晶高铬多元素合金系超硬耐磨层，可大幅提高易磨损设备及钢板制作件的使用寿命。

The Wear resistance of the high chromium cast iron designed for wear resistant layer is better than the original one.

在此工艺下可以得到界面结合良好的双金属复合材料；设计的耐磨层材料耐磨性明显优于原热镶装工艺所用材料。

It is concluded that the wear volume loss of ceramics Al2O3 is much lest than that of Si3N4 , but the wear volume loss of cast iron against Si3N4 is much lest than that against Al2O3 , and the friction coefficient is very small too .

结果表明：Al2O3陶瓷的磨损体积损失远小于Si3N4的，但灰铸铁与Si3N4配副时的磨损体积损失却大大小于与Al2O3配副时的，其摩擦系数也很小（0.02）。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。