查询词典 wear and tear

Pitch circle diameter: d = mz = 3X12 = 36 Tooth crown heights: ha = m (f0 + x)= 3X (l +0.5)= 4.5 Tooth High: hf = m (f0 + cx)= 3X (l +0.25-0.5)= 2.25 Tooth full height: h = ha + hf = 4.5 +2.25 = 6.75 Addendum circle Chemical pumps diameter: Da = d +2 ha = 36 +2 X4.5 = 45 Fixed string tooth thickness: Sxn = m (π/ 2 * cos2a + xsin2a)= 3X (1.387 +0.6428 X0.5)= 5.125 Fixed string of high gear tooth thickness measurement: hxn = m (π/ 8 * sin2a + xsin2a)= 3X (0.7476X0.117X0.5)= 2.42 Modulus coefficient x0.5 m3 O20 ° pressure angle tooth thickness Sxn5.12 fixed string Addendum Coefficient string f1 fixed gear tooth thickness measurement most high hxn2.42 Teeth z12 2, shaft wear and tear maintenance: Axis gear pump wear is mainly because with the support roller shaft at both ends between the friction and wear, so that smaller shaft diameter.

分度圆直径：d=mz=3X12=36 齿顶高：ha=m（f0+x）=3X（l+0.5）=4.5 齿根高：hf=m（f0+c-x）=3X（l+0.25-0.5）=2.25 齿全高：h=ha+hf=4.5+2.25=6.75 齿顶圆直径：Da=d+2ha=36+2X4.5=45 固定弦齿厚：Sxn=m（π/2*cos2a+xsin2a）=3X（1.387+0.6428X0.5）=5.125 固定弦齿厚测量用齿高：hxn=m（π/8*sin2a+xsin2a）=3X（0.7476X0.117X0.5）=2.42 模数m3变位系数x0.5 齿形角o20°固定弦齿厚Sxn5.12 齿顶高系数f1固定弦齿厚测最齿高hxn2.42 齿数z12 2、轴的磨损维修：齿轮泵中轴的磨损主要是因为轴两端与支撑滚针间的摩擦磨损，使轴径变小。

Gear wear and tear maintenance: Gear tooth wear is mainly the meshing parts, involute gear face and ends flat.

齿轮的磨损维修：齿轮的磨损部位主要是齿的啮合、渐开线工作面和齿轮两端平面。

Surfacing rock for strong wear-resistant mechanical parts, such as leaf blowers, concrete mixer blade, pink stone hammer machine, wood screw, such as carbon pieces easy to wear and tear of the surface repair.

适用于堆焊耐岩石强烈磨损的机械零件，如鼓风机叶片、混凝土搅拌机叶片、粉石机锤头、木碳机螺旋等易磨损件的表面修复。

Thankfully the Nokia E71 isn't exposed to wear and tear much, since its back cover is all metel, while the body is made of glossy plastic that won't wear off with time.

幸好诺基亚e71是不是暴露了磨损得多，因为它的封底是所有金属，而该机构所作的光滑塑料将不会磨损小康与时间。

The solution: find the plunger adjustable arm or gear from the speed control rod protruding ears slot prolapse, should re-open the fuel pump is installed correctly; also check whether the cross-slot wear and tear is too large, if found dead in parked for seca column position, should be demolition of repair or replacement parts; injector should be able to check the plunger is serious wear and tear, deputy returned to the oil valve gasket is worn; demolition injector, check whether the coupling of needle stuck in the closed position, needle and the injection hole Does burning, according to test results even to repair or replace parts.

解决办法：发现柱塞调节臂或齿轮凸耳从调速拉杆槽中脱出，应拆开喷油泵重新正确安装；同时检查叉槽是否磨损过大，如发现柱塞卡死在停供位置，应拆卸进行修复或换新件；喷油无力应检查柱塞副是否严重磨损，回油阀垫圈是否磨损；拆卸喷油器，检查针阀偶件是否卡死在关闭位置，针阀与喷油孔是否烧损，根据检查结果进行修复或更换偶件。

Both ends of the wear cap maintenance: Gear pump with cast iron end caps, wear phenomenon occurs after a slight revision in the plate mill level, more serious wear and tear on the grinding surface grinding machine should be revised in the flat.

两端盖的磨损维修：齿轮泵的端盖用铸铁制造，出现磨损现象后，轻微的可在平板上研磨修平，磨损比较严重时应在平面磨床上磨削修平。

Cr15Mo3 is chromium wear-resistant white cast iron, heat treatment of the microstructure of martensite matrix of chromium carbide + Paralympic +, macro-hardness of HRC 60 or more wear resistance than Ni-Hard Cast Iron It is a very good wear-resistant material that can be produced coal mill, ore crusher, cement mill, shot blasting machines, mud pump, slurry pumps and other wear and tear serious casting.

Cr15Mo3 是铬系耐磨白口铸铁，热处理后的金相组织为马氏体基体+铬的碳化物+残奥，宏观硬度HRC在60以上，耐磨性能优于镍硬铸铁，是非常好的耐磨材料，可制作磨煤机、矿石破碎机、水泥磨机、抛丸机、泥浆泵、渣浆泵等磨损严重的铸件。

Transit steering wheel is too large, instability manipulation check ball steering pump, master pins and bushings, wheel bearings wear, etc., such as wear and tear or serious gap exceeded, the repair should be adjusted.

方向盘转运过大，操纵不稳定检查转向泵球头、主销和衬套、车轮轴承等处磨损情况，如磨损严重或间隙超限，应调整修理。

Injector fuel supply or pressure is not enough, atomization bad, drip, etc.; plunger rod adjustable arm or teeth protruding ears from the governor lever fork slot prolapse in non-oil position; fuel pump plunger and barrel assembly seriously wear and tear, oil pressure is too low, the oil valve wear serious Mifengbuyan; washer crack and deformation, a broken valve spring, injector wear and tear stuck in the closed position.

喷油器不供油或压力不足、雾化不良、滴油等；柱塞调节臂或齿杆凸耳从调速杠杆叉槽中脱出处于不供油位置；喷油泵柱塞偶件严重磨损，供油压力太低，出油阀磨损严重，密封不严；垫圈开裂变形，出油阀弹簧折断，喷油器磨损卡死在关闭位置。

If there is no excessive wear or the time gap, they should check: First, the steering gear worm gear wear, or the required space, such as the gap is too large to be adjusted; Second, the shift device connected part of the wear and tear, or whether or not to adjust too loose; Third, the steering is loose parts installed; Fourth, there are loose steering arm down.

如无过大磨损或间隙时，则应检查：第一，转向器蜗轮蜗杆磨损情况，或间隙是否符合规定，如间隙过大应调整；第二，转向装置连接部分的磨损情况，或是否调整得过松；第三，转向器安装部位是否松动；第四，转向垂臂有松动。

Singer Leona Lewis and former Led Zeppelin guitarist Jimmy Page emerged as the bus transformed into a grass-covered carnival float, and the pair combined for a rendition of "Whole Lotta Love".

歌手leona刘易斯和前率领的飞艇的吉他手吉米页出现巴士转化为基层所涵盖的嘉年华花车，和一双合并为一移交&整个lotta爱&。

This is Kate, and that's Erin.

这是凯特，那个是爱朗。