查询词典 water pressure

CO2 and H2S exist in the hydrocarbon zone and foramtion water,as the accompany gases of petroleum and nature gaso or components of formation water,which will cause corrostion to the cement sheath under certain conditions of humidity and pressure.It will decrease the cement sheath's alkalinity,which results in the decrease of cement sheath's strength,permeability increase,and places a premium on fluid channeling and borehole wall sloughs accident in plastic formation,shortening the oil- gas well's production lifetime and giving rise to tremendous ecomonic losses.

CO2和H2S作为石油和天然气的伴生气或地层水的组分存在于油气层或地层水中，在一定的湿度及压力条件下会对固井水泥环产生腐蚀作用，从而降低水泥环的碱性，使水泥环强度下降，渗透率增大，并诱发流体窜流、塑性地层井壁跨塌等事故，从而缩短油气井的生产寿命，造成巨大的经济损失。

A cold-water supply system consists essentially of a communication pipe、a meter box、pressure boosters、storage taks、a piping line、valves and water-dispensing fixtures.

一个冷水给水系统的基本组成是：引入管、水表盒、增压设施、贮水箱、管道、闸阀和配水器具。

A data plate identifying your water heater can be found on the top of the water heater near the Temperature and Pressure Relief Valve.

在热水器顶部附近的降温减压安全阀上可以看到标示您的热水器的参数板。

For the first time spud drilling: at 22:00 on the December 31, 2009 using the 26 " drills, earth-moving polymer drilling fluid depth of 16.40m for the first time since the Park, the drilling, at 06:00 on January 4, 2010 to the depth of drilling 262.5m, horizons Upper.fars Group at its first drilled, January 5 Electrical Measurement finished, at 04:00 on the 6th, under 20 " cementing casing to the depth of 261.50m, water, mud back to the ground, the cement plug surface depth of 248.50 m, casing pressure test with water 10.0MPa qualified, January 8 cementing electrical measuring the quality of finish, drill cement plug at 20 o'clock on the 10th end, the end of a job opening.

下面这段中文，希望网友帮忙译为英语：第一次开钻钻进：2009年12月31日22：00使用26&钻头、搬土聚合物钻井液自园井深16.40m第一次开钻，2010年1月4日06：00钻进至井深262.5m，层位Upper.fars组第一次完钻，1月5日电测完，6日04：00下20&套管至井深261.50m固井，水泥浆返至地面，水泥塞面井深248.50m，套管清水试压10.0MPa合格，1月8日电测固井质量完，10日20：00钻水泥塞完，结束一开工作。

Open flame ignited, the combustion gasification burner in the open through the combustion air blower without any pressure, the fuel soluble in water, once the accident fire, water or foam to fight.

用明火点燃后，燃烧气化在敞开的燃烧器内通过鼓风机助燃，无任何压力、该燃料溶于水，一旦意外着火，用水或泡沫灭火器扑救即灭。

Compared to atmospheric pressure hot water boiler, operational principle and characteristic of vacuum hot water boiler are narrated.

叙述了真空热水锅炉的工作原理、特点以及与常压热水锅炉的性能比较。

When the density of the eyedropper and the water and air inside it is greater than that of water, it sinks. When you stop squeezing the bottle, the pressure decreases and the eyedropper floats.

当滴管及管内的水和空气的密度比水的密度大时，滴管就会下沉；当你停止挤压汽水瓶，压力减小，滴管就会浮起。

The water inside a horizontal vessel is heated by fired burner through burning channel, and the natural gas or crude oil in tube bundle or high pressure coil are heated by hot water.

燃烧器燃烧后通过燃烧道加热水平容器内部的水，然后利用放置在水中的高压盘管或管束加热其中的天然气或原油。

At the same time, the car water pump is prone to suffer from cavitation erosion at the entrance of the water pump . So installing a low-pressure radiator cap is usually a useful help.

气蚀是汽车水泵的另一个问题，一般在水泵的进水侧会出现腐蚀，所以通常都安装一个低压散热器盖。

After the replacement of the toilet tank fittings, toilet transformation and waterproof plugging for home decoration users Heating modification and test pressure, cast iron radiator displacement, high-grade radiator installation, unit radiator repair transformation, specializing in heating does not heat, converted a second floor and multi-storey high-rise independent water, rain water pipe replacement and installation residential buildings, walls and floor drilling, trenching and demolition, mechanical cleaning of various drains.

提供 承接家庭、单位及小区老旧管道更新、更换，自来水查漏，解决各种管道疑难问题，对突发漏水管道24小时抢修、快修，对家庭提供日常维修服务，修换水阀、软管、水龙及地漏等，维修马桶、洗手盆、洗菜盆等，更换马桶后水箱配件，卫生间改造及防水堵漏，对家庭装修用户进行暖气改装及试压，铸铁暖气片移位，高档暖气片安装，单位暖气片维修改造，专修暖气不热，改装一、二楼及多层高楼独立下水，居民楼雨水管更换安装，墙地面钻孔、挖沟及拆除，机械疏通各种下水道等。

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时，滚道或滚动元件褪色是很常见的特征。