查询词典 volcanic cone

This paper referred to simulating the supersonic double cone inlet" s flow field of ramjet pill assisted range projectiles at a variety of working circumstances, pressure contours, density contours and Mach number contours of inlet" s flow field were given When cone combination, relative location of cone core and cowl lip, the pressure of outlet, inflow Mach number and angle were changed, flow field and performance parameters of inlet can be affected. Simultaneity, productive mechanism and inducing factors of the inlet surge were also discussed. Then the best working conditions and the best model of inlet were obtained.

本文对冲压增程弹丸所用发动机的双锥超声速进气道在各种工况条件下的流场进行了数值模拟，给出了进气道流场的等压线图、等密度线图和等马赫线图，从而观察在不同的锥尖角组合、锥芯与外罩唇口的相对位置、出口反压、来流马赫数和攻角时，对进气道流场及性能参数的影响，并探讨喘振现象的产生机理及诱导因素，以便确定最佳的工作状态，得到最优的进气道模型。

The essay is about the teaching research into the relations between the definition geometrize nature and circular cone , in which the teaching research of definition mainly uncovers the nature of circular cone;geometry nature about how to lead the students to understand the geometry nature of circular cone with equations in the thought of figures and shape.

其中定义的教学探究主要是揭示圆锥曲线的本质特征，几何性质的教学探究主要引导学生从方程的角度，用数形结合的思想去理解圆锥曲线的几何性质。

At first step, the processor before the deformable body contact the end face of cone die cavity regarded as an extrusion process. The minification of core boss's cross-section regarded as compressibility of direct extrusion, which acted as definition factor when construct the Direct Extrusion Model element. Another step, the model element of flat punch extrusion on wedge piece process was constructed when propose the process of deformable body overflow die corner. In this way the spherical end face of blank looked as cone end face one, t he approximate treatment is one of originality innovation in this paper. At last, the two elements have been connected and constructed the model element of cone boss part's deformation in the open die forging.

对于锥形凸台成形的第一个特征时段，即坯料和锥形凸台型腔的端面接触之前的变形过程，本文将凸台的截面缩小率转换成挤压成形的压缩率并以此为界定，建立了不同截面缩小率时的锥形模正挤压的模型单元；对于锥形凸台成形的第二特征时段即锥形模的角部充满过程，在详细考察锥形型腔端面对变形过程影响的基础上，将变形体的球形端面近似成锥面建立了平冲头挤压楔形体的模型单元；最后将前述两种模型单元有机连结，构建了开式模锻中整个锥形凸台成形过程的定量描述。

Unfortunately, the flare end of the Foley will not fit through the otoscope cone and you need to disconnect the cone from the light source and leave the cone with the catheter until the catheter is removed from the patient.

不幸的是，年底爆发的福利不适合通过耳镜锥和你需要断开锥从光源和离开锥的导管，直至导管脱离耐心。

The results show that, with the expansion cone angle remaining unchanged, the sizing length of expansion cone does not have much effect on the residual stress of casing after expansion, but it has much effect on the expansion force required by tube expansion. The expansion cone angle has no effect on the maximum residual stress of casing, but it has remarkable effect on expansion force. When the radial component force of expansion force is greater than the material's tensile strength, the damage to the material will arise.

研究结果表明，在膨胀锥锥角保持不变的情况下，膨胀锥定径长对膨胀后套管的残余应力没有太大影响，但对套管膨胀所需要的膨胀力有较大影响；膨胀锥锥角对套管最大残余应力没有影响，但对膨胀力的影响十分明显，当膨胀力的径向分力大于材料的抗拉强度时，材料将发生破坏。

Judging on the radioactive rays whether they penetrated through the truncated right angle cone shield configuration. A hypothetical circumscribed rectangular parallelepiped of the they penetrated through the truncated right angle cone shield configuration. A hypothetical circumscribed rectangular parallelepiped of the truncated right angle cone shield configuration is also presented. The methods simplified the camber equation and reduced the calculation time significantly.

在判断放射线是否穿透此圆锥台体时，又提出了圆锥台形屏蔽体的假想外接长方体的建模方法，将曲面方程联立解的复杂计算简化为一次代数方程的简单计算，大幅度地缩短了计算时间。

An accurate measurement scheme is proposed for testing the error of cone prisms with Hartmann wavefront sensor. The measurement theory was discussed, the reconstruction of the wavefront reflected from a cone prism was studied, and the relation between the wavefront characteristics and the errors of a cone prism was given.

因此，提出一种用哈特曼波前传感器全面检测角锥棱镜角度误差和面形误差的技术方案，从理论上分析了哈特曼法的测量原理，深入研究了光经过角锥棱镜后的波面重建，给出了波面特征与角锥棱镜误差参量之间的关系。

We obtain the closedness and semicontinuity of cone efficient solution sets and cone weakly efficient solution sets for multiobjective programming problem under constraint cone perturbations.

得到了约束锥扰动多目标规划问题的锥有效解集和锥弱有效解集的闭性和半连续性。

Meanwhile, we have gotten stability for the subdifferential of cone efficient point sets and cone weakly efficient point sets of multiobjective programming with respect to perturbation of cone respectively.

对于局部凸拓扑向量空间的多目标规划问题，本文研究并得到当确定空间序的控制锥受扰动，它们的锥有效点集和锥弱有效点集分别在锥次微分和锥弱次微分意义下的稳定性结果。

Cone of tangent; tangent cone; tangent-directrixed cone

选取要包括在拔模线中或从中排除的参照曲线段。。。。

The witness also told the jury at the Royal Courts of Justice in London that he saw a paparazzo fighting with a member of the public who was trying to stop him taking pictures in the minutes before the emergency services arrived.

他还告诉在伦敦皇家法庭的陪审团，在急救服务到来之前，他当时看见一个狗仔队正和一群阻止他拍照的人打架。

The entire N／C program on a tape is made up of an accumulation of these successive data blocks.

纸带上的整个数控程序由这些连续数据单元连接而成。