查询词典 vinyl resin

It was also found that the decrease of immersion resistance and impedance of the commercial anti-corrosion of poly (vinyl chloride co-isobutyl vinyl ether) coating with increase of directly adding of nano-TiO2, which was elucidated with the theory of critical pigment volume concentration. At last, the optimal coating prescription was gotten as follows: 0.5-1.0g nano-TiO2 B, 25.6g resin, 33.4g xylene, 1.4g chlorinated paraffin, 1.5g 15% slurry of organic bentonite, 0.8g green chrome, 7.7g grey mica ferric oxide and 0.6g non-float aluminum.

直接添加纳米二氧化钛的商品化防腐涂层耐浸泡性能和交流阻抗值随添加量增加而降低，利用临界体积浓度理论等解释了该现象；通过实验获得了如下最佳涂料配方为：0.5-1.0g纳米TiO2，25.6g氯醚树脂，33.4g二甲苯，1.4g氯化石蜡52＃，1.5g 15%有机膨润土浆，0.8g氧化铬绿，7.7g云母氧化铁灰，0.6g非浮型铝粉。

Resins: gum dammar; PU dispersion; silicone resin, epoxy resin, alkyd, acrylic Resin, polyester resin, urethane resin, polyamide resin, amino hardener; two pack hydroxy acrylic, two pack isocyanate-free acrylic; vinyl chloride co-polymers, polyvinyl butyrals, thixotropic resin.

树脂类：达玛树脂；水性PU分散体；有机硅、环氧、醇酸、丙烯酸、聚酯、聚氨酯、聚酰胺、氨基固化剂；双组份羟基丙烯酸、双组份不含异氰酸脂丙烯酸；聚氯乙烯共聚物、聚乙烯醇缩丁醛、触变性树脂。

The company's products include: silane coupling agent KH-550, KH-560, KH-570, KH-602 and other models, perchlorethylene resin, high-chlorinated polyethylene resins, pigments, PCE, ethyl cellulose, poly vinyl perfluoro-C (F46 fluorine resin) silicone oil, dichloromethane, dichloroethane, cyclohexanone, protopine, ion exchange resin, epoxy resin, PF and other chemical raw materials, are manufacture of fine chemicals, adhesives, paint remover, paint, paint, antifreeze and other products of the basic raw materials.

本公司经营的产品有：硅烷偶联剂KH-550，KH-560，KH-570，KH-602等型号，过氯乙烯树脂、高氯化聚乙烯树脂、颜料、四氯乙烯、乙基纤维素，聚全氟丙乙烯树脂（F46氟树脂）硅油、二氯甲烷、二氯乙烷、环己酮、片碱、离子交换树脂、环氧树脂、PF等各种化工原料，是制造精细化工，粘合剂，脱漆剂，涂料，油漆，防冻液等产品的基本原料。

Can be used as base metal coating materials used vinyl resin system by plastisol or solution, polyester or acrylic, etc.

可以作为金属涂布的底基材料使用的树脂系统有乙烯、聚酯或丙烯酸等。

The Solidification temperature range was defined as 110-200℃ by DSC analysis. More accelerant used can increase the casing samples dynamic performance, but more than enough accelerant can induce a severe solidified reaction that result in a smaller polymeric meshwork and reducing the sample's performance. Normally the Accelerant dosage can be 2 portions; The Epoxy resin CFRP has a obvious better performances than the Vinyl-ester Resin CFRP, i.e. had a Bend Strength of 1516MPa, LSS of 85MPa, also Tg raised to 195~C~ When used the end-carboxyl polyether to reinforce the epoxy resin, the casing sample's SS, BS and Crack Elongation all increased geminately. The CFRP performance also increased a little, that is because the performance of the CFRP mainly contributed by the CF. The reinforced resin improved the interface between the CF and resin that contribute to the little increasing.

通过DSC分析确定了该环氧树脂的固化温度范围为110~200℃，促进剂增加会提高浇注体力学性能，但过多的促进剂会使固化反应剧烈，聚合网络减小，使浇注体性能下降，一般用量为2份左右；以环氧树脂为基体的复合材料性能明显比以乙烯基酯树脂的性能提高，弯曲强度达到1516MPa，层间剪切强度达到85MPa，同时Tg也上升到195℃；用端羧基聚醚增韧环氧树脂后，其浇注体的拉伸强度、弯曲强度及断裂伸长都成倍增加，复合材料的性能也有所提高，但提高幅度不大，因为复合材料的力学性能主要由碳纤维承担，树脂增韧后改善了复合材料的界面性能。

Water-based resin approximately150, such as Rosin monomaleate monomaleate, styryl, acrylic copolymer resins, such as aminosulfonic ethylacrylate, emulsio, that is, there is a water-based dispersion resins, vinyl acetate copolymer, acrylic copolymer, polyurethane resin, epoxy resin, etc.

水性树脂的种类很多，如松香马来酸树脂、苯乙烯马来酸树脂、丙烯酸共聚物、氨基丙烯酸乙酯等，高分子乳液，即水性分散树脂，有醋酸乙烯共聚物、丙烯酸共聚物、聚氨酯树脂、环氧树脂等。

By using Balsa wood, paulownia wood, quasi-orthogonal E-glass non-woven fabric and vinyl resin, two types of light-weight high-performance sandwich composite matting were fabricated by the advanced vacuum infusion molding process, the masses of which are 15 kg/m^2 and 20 kg/m^2, respectively.

选用Balsa轻木、泡桐木、玻璃纤维布以及乙烯基酯树脂，采用先进的真空导入成型工艺制备出2种轻质高强的复合材料道面垫板，其质量分别为15、20 kg/平方公尺。

The morphological structure of cured vinyl-ester resin and the formation of two-phase structures in vinyl-ester resin has been studied by using SEM and differential scanning calorimetry.The results demonstrated the existence of clusters of gel-particles with a size of about 20 μ m,each cluster of gel-particles containing many gel-particles with coral-like structures.The formation of gel-particles resulted in two-phase structure characterized by the two peaks in the rescanned DSC thermographs of the resin. The cure conditions (temperatures,post-cure) affected microstructure in the cured resins.

采用SEM、DSC研究了乙烯基酯树脂固化过程中凝胶粒子的形成过程及两相结构对固化放热的影响，结果表明，凝胶粒子在固化树脂中呈群状分布，每群凝胶粒子的最大尺寸为20μ m左右，每群凝胶粒子由许多独立凝胶粒子组成；凝胶粒子的形成使树脂产生了两相结构，使树脂的恒温DSC残余放热呈双峰分布；树脂的固化条件影响其微观结构。

Australian Vinyls Corporation Limited is Australia's only local manufacturer and supplier of vinyl resin.

澳大利亚Vinyls有限公司是澳大利亚当地唯一的PVC树脂生产商和供应商。

The corresponding relations between the strain of the static state and dynamic cycle load and the volume resistance of the short chopped carbon fibers, short chopped carbon mat, unidirectional carbon fibers reinforced vinyl resin composites is existed. The physical modes of these kinds of composites are also designed based on the experiment data. The resistance and strain of the short chopped fibers reinforced vinyl composites satisfy the equation of y =A + Bx + Cx~2 in the static strain test method and the short chopped mat reinforced vinyl composites is y = A + Bx.

短切碳纤维、短切碳纤维毡、单向碳纤维增强乙烯基酯树脂复合材料在静态和动态循环载荷下，应变与电阻之间有较好的对应性，同时根据实验数据，建立了不同条件下该复合材料应变和电阻变化规律的物理模型，短切碳纤维增强乙烯基酯树脂复合材料在静态拉伸时电阻与应变之间满足：y=A+Bχ+Cχ~2；碳纤维毡增强乙烯基酯树脂复合材料在静态拉伸破坏时电阻与应变之间满足：y=A+Bχ。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。