查询词典 valve housing

The demolition was found, M6 wire plug off, but not in the valve housing, the last in the radiator inlet discovered.

经拆卸后发现，M6丝堵脱落，但并不在阀壳体内，最后在散热器的进油口处发现。

Gas outlet ports are formed at opposite longitudinal sides of the valve housing.

在阀壳的相对纵向侧面形成出气孔。

The surface of the valve housing is zinc coated.

阀体表面镀锌处理。

The shortcoming of top valve housing for standard type oil well pump plunger is wear and rupture of oil flow pore wall.

标准型抽油泵柱塞上阀罩的工作缺陷是出油孔壁磨损断裂。

The temperature and stress in valve housing of medium cylinder in super critical steam turbine during cold start and under nominal load were calculated with FEM cord NASTRAN.

采用大型有限元分析软件NASTRAN，对超临界1000 MW汽轮机中压缸主汽阀阀壳的冷态启动过程和额定工况下的温度场和应力场进行计算，得到了冷启动过程中阀壳的温度和应力分布规律，并将冷启动结束时的计算结果同额定工况下的计算结果作一对比分析。

Based on the FEM,the calculation and analysis were performed for the transient temperature field s and stress fields of the intermediate pressure main steam valve housing under various operating conditions including cold startup,shutdown,strong hot startup,limit hot startup and accidental condition in 200MW unit in power station.

采用有限元方法，计算分析了电站200MW汽轮机中压主汽阀阀壳在冷启、停机、强热启动、极热启动以及事故等工况下的温度场和应力场，得出了阀壳裂纹区各工况下温度场和应力场的变化规律，提出了内壁裂纹区的周向应力是疲劳寿命计算的主要参考量。

Based on the FEM,the calculation and analysis were performed for the transient temperature fields and stress fields of the intermediate pressure main steam valve housing under various operating conditions including cold startup,shutdown,strong hot startup,limit hot startup and accidental condition in 200MW unit in power station.

采用有限元方法，计算分析了电站200MW汽轮机中压主汽阀阀壳在冷启、停机、强热启动、极热启动以及事故等工况下的温度场和应力场，得出了阀壳裂纹区各工况下温度场和应力场的变化规律，提出了内壁裂纹区的周向应力是疲劳寿命计算的主要参考量。

The scope of their business is: producing aluminum castings, such as brake caliper, master cylinder, engine bracket, intake manifold, steering housing, valve, compressor housing and all the demands of high-quality products in the field including the auto industry, electronics industry and hydraulic industry.

其经营范围：制作铝合金铸件、生产缸体、制动钳、发动机支架、进气岐管、转向伐体、阀体支架、涡轮增压器、壳体以及所有要求高质量的零件：汽车工业、电子技术工业、液压工业等。

Valve housing and components used, such as the United States and build the Association ASTM standards, has monel, titanium, zirconium material, tantalum material Hastelloy, ultra-low carbon, alloy steel, stainless steel, carbon steel, etc..

阀门壳体及零部件采用美材协ASTM等标准，有蒙乃尔、钛合金、锆材、钽材哈氏合金、超低碳、合金钢、不锈钢、碳钢等。

The most important are as follows: Detection of type: valve stem seal leakage test and test; water valve tightness test; switch tightness test; the take-off safety valve Test; Detection Object: valve, the cut-off valve , safety valve, throttle valve, check valve, swing check valve, ball valve, regulating valve and other hollow pump body, valve body and housing, etc.; way valve connection: flange connection, threaded connection, welding connection; detection medium.

最重要的有以下几种：检测类型：阀门密封性试验及阀杆泄漏性试验；水中阀体密封性试验；开关密封性试验；安全阀的起跳值试验；检测对象：闸阀、截止阀、安全阀、节流阀、止回阀、摆动式逆止阀、球阀、调节阀和其他中空的泵体、阀体和壳体等；阀门联接方式：法兰联接、螺纹连接、焊接联接；检测介质。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。