查询词典 valve body

Vent the piping and test valve body cavity to remove air or steam.

排放管道和试验阀门体腔内的空气或蒸汽。

When full-opening, the angle off of ball body and valve body via axes no more than 3°.

阀门全开时，球体通孔轴线与阀体通孔轴线的夹角不大于3

Install the valve in the line with the arrow on valve body pointing in the direction of flow.

将阀门安装在管线上时要使得阀体上的箭头指向水流方向。

Install the valve in the line with the arrow on valve body pointing in the direction of flow.

要按照阀体上的箭头方向在管线上安装阀门，使得箭头方向与流体流向相同。

Gas valve body material selection Pressure gas pipeline under the reasonable use of the valve housing material selection, not only palace to meet the safe operation of pipeline and is able to reduce the cost and make the best use for the purpose.

三、燃气阀门的阀体材质选用根据燃气管线的使用压力合理选用阀门壳体材质，既宫满足管线的安全运行又能达到减少造价，物尽其用的目的。

Soft sealing gate valve body, valve cover using precision casting in metal, a shape, the basic non-mechanical processing, do not use sealed copper ring, saving non-ferrous metals.

软密封闸阀的阀体、阀盖采用精密铸造法铸造，一次成型，基本不机械加工，不使用密封铜环，节约有色金属。

In this tutorial, the assembly is a simple valve and the first part placed is the valve body.

在本自学课程中，组合为简单的阀，置入的第一个零件是阀本体。

This article describes a one-way valve fuel control valve body design and plastic mold design process.

本文说明了加油管单向阀阀体设计及塑料模具设计的全过程。

The opening of the valve body in a leading role in the orientation of any reciprocating parts, in the active pieces into fixed at the minimum radial clearance of not less than 0.7mm, valves should be in a spy state, the activities of parts and fixed parts Minimum radial clearance of A42C Type Pound-Grade Low Lift Spring Loaded Safety Valve not less than 0.125mm.

阀体中对阀的开启起主导作用的任何往复运动的导向零件，在活动件进人固定处的最小径向间隙不应小于0.7mm，阀处于伺应状态时，活动件与固定件的最小径向间隙不应小于0.125mm。

The opening of the valve body in a leading role in the orientation of any reciprocating parts in the active pieces into fixed at the minimum radial clearance of not less than 0.7mm valves should be in a spy state the activities of parts and fixed parts Minimum radial clearance ofA42C Type Pound-Grade Low Lift Spring Loaded Safety Valve not less than 0.125mm.

阀体中对阀的开启起主导作用的任何往复运动的导向零件，在活动件进人固定处的最小径向间隙不应小于0.7mm阀处于伺应状态时，活动件与固定件的最小径向间隙不应小于0.125mm。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。