查询词典 upon the die

Behold, the hand of the LORD is upon thy cattle which is in the field, upon the horses, upon the asses, upon the camels, upon the oxen, and upon the sheep: there shall be a very grievous murrain.

9：3 耶和华的手加在你田间的牲畜上，就是在马，驴，骆驼，牛群，羊群上，必有重重的瘟疫。

Behold, the hand of the LORD is upon your cattle which is in the field, upon the horses, upon the asses, upon the camels, upon the oxen, and upon the sheep: there shall be a very grievous murrain.

003 耶和华的手加在你田间的牲畜上，就是在马、驴、骆驼、牛群、羊群上，必有重重的瘟疫。

The system could complete parameterized design of parts and die parts drawing, the virtual assemkbly of die and die assembly drawing, and animated die drawing.

并基于SolidEdge平台，采用参数设计技术和VisualBasic工具，开发了一个圆筒形零件拉深模具系统，该系统能够全参数化进行零件设计并生成零件图、模具虚拟安装并生成模具装配图。

Put die on the die seat, adjust cross- plate and transducer draging plate of up and down, so that the steel needle can be inserted into die hole to adjust the pressure of weight, and then place the abrasive, open power switch of ultrasonic and rotating switch of die seat.

模具放在模座上，调节十字脱板及换能器上下拖板，使钢针插入模孔内，调整砝码压力，然后放上磨料，打开超声波电源开关和模座旋转开关。

With the help of the concepts of Lebesgue measure and Lebesgue integral in real function,the mathematics model of concurrent design of life-oriented progressive die is advanced. Which were the Lebesgue measure and Lebesgue integral of die substructures and a general mathematics model of the relation between progressive die structure and die substructures.

运用实变函数中的Lebesgue测度和Lebesgue积分的概念，结合面向寿命的级进冲模并行设计的特点，建立了面向寿命的级进冲模并行设计数学模型—模具子结构的Lebesgue测度和Lebesgue积分，提出了级进冲模结构与模具子结构关系的一般数学表达式。

The pattern of camber die-drawing are optimized. The physical innate character of drawing with camber die is analyzed thoroughly. For the first time, the periodical relation between the limit drawing coefficient and the large longitudinal stress in dangerous section is established. Furthermore, the rationale to judge limit deforming degree is developed. Then, the limit drawing coefficient of drawing with camber die is proposed. Based on the criterion that the large stress in flange is smaller than that of limit value, the formula of drawing with camber die without wrinkles is deduced.

对拉深凹模的型式进行了优化；深入地分析了曲面凹模拉深成形的物理本质，首次定量地确定了极限拉深系数与危险断面最大径向应力的关系，提出了判断极限变形程度的依据，分析了极限承载能力，建立了曲面凹模拉深的极限拉深系数的表达式；以凸缘切向最大压应力小于凸缘切向压应力临界值为准则，推导出了曲面凹模拉深不起皱的理论表达式。

Select high-quality die-cutting tool to be considered depending on the die-cutting materials of munltivariable and gaofeng and gaofeng coilia, short peaks can cut thin paper knife and cut thick paper, you can use the automatic single die-cutting, it may be used at the same time cutting two or three sheets of paper-a set of die-cutting, use a wide range.

选择优质的模切刀时应注意根据所模切材料的厚薄而选择高峰刀及矮峰刀，高峰刀既可以切薄纸又可以切厚纸，既可以用在单张的自动模切机上，又可以用在同时模切二、三张纸的手摇模切机上，使用范围很广。

Deep drawsmay be made on single-action dies,where the pressure on the blankholder is more evenly controlled by a die cushion or pad attached to the bed of the press,The typical construction of such a die is shown in Figure 10-6.this is an inverted die with the punch on the die's lower portion

深drawsmay作出对单动去世后，那里的压力就压边的是，更多的控制，由一个模垫或垫附于床的新闻，典型建筑这样一个死硬的是表现在图10 - 6.this是一个倒模与冲床对模具的上半部分。

Besides expressing design result, it provides domain constraint for design process and model information for digital assembly sequence planning and simulation of stamping die, which is usually ignored in the former product models. Taking the specific structure and design process of stamping die into account, the information of workpiece is composed in die product model as product feature. Former product models merely contain mainly about the die design result, this model extends the contents of product model with the relation feature of the composed subassembly and parts and also other associated production knowledge. It is convenient for getting the associated information during intelligentized design process.

该模型不但能完整地表达冲模的设计结果，同时还表达和存储了冲模设计的知识信息，能较好地为冲模的设计过程提供规则和约束，支持产品的智能设计过程以及冲模的数字化预装配规划和仿真；而模型中冲压件信息的集成则扩大了冲模产品模型的信息内涵和应用外延，便于建立冲模智能设计过程的信息关联，从而使集成信息模型成为产品设计过程上、下游活动实现信息共享的基础。

It will be drawn into the die without allowing wrinkles to form Another type of drawing die for use in a single-action press is shown in Figure10-4 this die is a plain single-action type where the punch pushes the metal blank into the die ,using a spring-loaded pressure pad to control the metal flow.

它会被卷入模具而不让皱纹形成另一种类型的拉丝模使用于单动压力机是表现在图形10 - 4这个模具是一个浅显的单动式如冲床把金属毛坯到死了，用弹簧垫，以控制金属流。

A carrier gas such as nitrogen is directed through line 20 and valve 22 to connect with line 26 and mix with the gas sample.

如氮气之类的载体通过管线20和阀22引入，与管线26相通，与气体样品混合。

But for the most part, knaves and parasites had the command of his fortune

然而支配他的家产的大多是恶棍和寄生虫。