查询词典 unscrew

Unscrew 2 screws fastening paper cartridge and lower cover , take out the cartridge.

宁开纸仓与下盖固定的两枚螺丝，取出纸仓

A man dining alone was trying to unscrew the cap of a bottle of catsup but his fingers were so badly crippled by arthritis that he couldn't do it.

译：一个独自用餐的人正试图打开番茄酱的瓶盖，但他的手指因关节炎而留下严重残疾，拧不开瓶盖。

Using a Chemtrol spanner wrench1, unscrew the seat-carrier (Tru-Bloc Model-C) by rotating in the counterclockwise direction.

使用一把Chemtrol活动扳手1，通过逆时针方向旋转拧松阀座支架(Tru-Bloc型号C)的螺纹。

To set the Date or Time with Screw Crowns:Setting the time and date with a screw down crown watch is the same as above;however to pull out the crown you must first"unscrew"the crown by turning it in a counter clockwise direction until the crwn releases from the threaded tube.

鲁美诺思Luminox 海豹系列产品中英文使用说明书（适用于6102，3105等海豹三针系列产品）☆☆注意：请先仔细看本说明书。本款手表和普通手表不同，调时间旋钮不是直接往外拔的，有防水螺纹管，所以要首先逆时针拧动旋钮，直到旋钮从螺纹管旋出。

Magnetic axis can guarantee there is sufficient pressure to maintain their connection strong, so that you can unscrew the diaphragm.

可以保证电磁轴有足够的压力，保持其连接稳固，这样就可以旋下隔膜。

Remove shear pin (28) and unscrew bearing cap (16) using a 24ln pipe wrench.

取走剪销(28)，用24管钳拧下轴承盖(16)。

Unscrew packing gland (9) from the bonnet (2) using a 24ln pipe wrench.

用24管钳从阀罩(2)上拧下盘根压帽(9)。

At that moment I was very busy trying to unscrew a bolt that had got stuck in my engine.

在那一刻我感到非常繁忙，试图unscrew一螺栓了，卡在我的引擎。

Unscrew the locking nuts on the release lever, meanwhile unscrew the adjusting nuts using a spanner, while doing that measure the gaps between the release levers and bearings by means of feeler gauge, until the gap reads 0.3-0.5mm. Repeat it for three release levers, their gaps should be the same, after that screw up the locking nuts, and check it to make sure.

b、旋松分离杠杆上的锁紧螺母，一面用扳手转动调节螺母，一面用厚薄规测量分离杠杆与分离轴承之间的间隙，直到间隙为0.3-0.5毫米为止，三只分离杠杆依次都调整好，再将锁紧螺母锁紧，然后复查一遍。

B. Unscrew the locking nuts on the release lever, meanwhile unscrew the adjusting nuts using a spanner, while doing that measure the gaps between the release levers and bearings by means of feeler gauge, until the gap reads 0.3-0.5mm.

b、旋松分离杠杆上的锁紧螺母，一面用扳手转动调节螺母，一面用厚薄规测量分离杠杆与分离轴承之间的间隙，直到间隙为0.3-0.5毫米为止，三只分离杠杆依次都调整好，再将锁紧螺母锁紧，然后复查一遍

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。