查询词典 unmelted

The grain size of the coating was 100~400nm. The nano-grains resulted from the re-crystallization of melted and partially melted nanoscale powders and some unmelted nanoscale powders preserved in the coating.

涂层的孔隙率大约为19%；纳米—亚微米MoS_2涂层的物相主要为六方的MoS_2，还有少量的Mo，Mo_2S_3和MoO_3，涂层由片状MoS_2组成，尺寸在100～400nm。

In the process of continuous casting, the unmelted carbon granules in the mould powder were mixed into steel liquid and became inclusions.

在连铸过程中，结晶器保护渣中未熔融的碳粒子进入钢液，在铸坯内部形成夹杂，经过热轧、穿孔之后，游离碳夹杂沿轧向伸长、呈螺旋状分布，在基体材料的晶界上偏聚，造成晶粒边界的成分不均匀。

Li reduces the surface tension of aluminum luquid obviously, increases the ratio and rate of heterogeneous nucleation, which is the necessary condition of the formation of fine grains. However, a large amount of unmelted Al3Sc, Al3Zr TiAl3 particles dispersively distribute in the luquid metal along the edge of the molten pool, which is the sufficient condition of the formation of fine grains.

Li显著地降低了铝液表面张力，大大提高了异质形核率和形核速率，是细晶层产生的必要条件；而熔池边缘液态金属中弥散均匀分布大量未熔化的Al_3Sc、Al_3Zr和TiAl_3质点，则是细晶层产生的充分条件。

The rapid solidification and grain growth of molten bath of laser surface remelting TA15 titanium alloy was a process of directly epitaxial growth of the b grains of the unmelted substrate at the contact of the melt-pool bottom.

分析表明，TA15钛合金激光表面重熔熔池的快速凝固是一个以熔池底部热影响区顶部与熔体接触的未熔母材b晶粒为衬底的直接外延生长过程，因此热影响区顶部与熔体接触的未熔母

Mould slag entrapment brings out the phenomenon of break wire in the drawing of high-purity steel C72DA.Through studying mould flow field,conclusion is considered that mould slag entrapment is near the mould wall and is caused by serious undulation of the steel level,the hot metal bias or unmelted mould power.

结晶器卷渣引起高纯净度的C72DA钢在拉拔过程中出现断丝现象，通过对结晶器流场的研究，认为结晶器卷渣主要在结晶器壁附近，是由于表面钢水的波动严重、钢水偏流、或保护渣熔化不良引起的。

LTHJ-SUPER-A2 welding manipulator automatic recovery machine(Condensed air is needed0.4-0.8Mpa) This system is set for welding manipulator,special cylindrical welding tools or difficult welding .It adds super negative pressure wind pump on inner side offlux cylinder,so that in the welding process it can absorb unmelted flux directly into cylinder and place into a small hopper.Open the valve of small hopper and put flux onto work piece,then you can put it into reprated usage.

LTHJ-SUPER-A2型操作机正压自动回收机（需压缩空气0.4-0.8Mpa）本系统是为一体超强新型的操作机或外圆焊接特制工具、高难度的焊接而设置的，它利用压缩空气，将在焊接过程中尚未溶化的焊剂直接吸收到桶内，放置到小料斗中，打开小料斗阀门把焊剂放到工件上，进行往复使用。

It uses a low temperature supersonic gas jet （ typically below 600℃） to accelerate unmelted solid powders over a critical velocity at which particles impact on the substrate, deform plastically and mechanically to form the coating.

它是利用低温（一般低于600℃）超音速气体射流加速喷涂粒子，使粒子不熔化，以固态形式与基体发生塑性碰撞而实现涂层沉积。

It has the same style with LTHS100E, however, its functions were improved based on the old style; at present, LTHS100B applies imported wind pump assembly which has twice theme ---absorb and blow (increase parts on positive pressure air, strengthen the pressure that can deliver the unmelted flux directly into little hopper); the height of material absorbing and delivering can reach as high as 5 meters, and its level distance is around 12 meters, and the capacity of flux depends is 80KG; the suspended function also can be tailored according to customers' requirements; the weight of 100B is 130KG, its outer dimension is 450*800*1100mm. It has the advantages of small-volume, light-weight, beautiful-outer-appearance, unnecessary of air-compression, and can be ground-mounted or suspended; it is also easy to be operated, with switching on button, it can be operated. Furthermore, it is controlled by infrared ray. It has alarming lights.

该机与LTHS100E机形相同，但其主要特点：在LTHS100E的基础上精心整改了其功能，现LTHS100B是采用进口风泵总成为基础，吸、吹二次全部为主题（在正压气上增加了部件，增强了压力把吸收回来没有融化的焊剂直接推送到前方机头的小料斗内，）焊剂的吸、送料其高度不得超过5米，水平距离在12米左右，焊剂容量为80KG，可悬挂也可根据用户需要为用户量身订制，自重为120KG，外型尺寸为：450*800*1100mm，本机具有体积小，重量轻，外型美观，不需要具备压缩空气，可落地、可悬挂灵活，其操作简便为一线通即可，红外线控制，上方有警示灯显示，当焊剂不足时就会报警。

On the basis of examination of the wear behavior and worn surface morphology of the coatings after abrasive wear and erosion wear respectively, and the enhancing mechanisms of interlamellar bonding caused by unmelted carbide particles during deposition, the effects of the microstructure on its performance are discussed.

其次， 在分析研究了涂层磨拉磨损和冲蚀磨损失效形貌以及未熔化碳化物颗粒对涂层层间结合强化机理的基础上，探讨了磨损机制、磨损模型的建立及涂层结构对磨损性能的影响规律。

The microstructure of plasma spraying coating doping nanometer Al2O3/ZrO2 was complicated. The particular structure include cylindrical micrometer crystal enwraped in putamina consist of nanometer ones, unmelted ZnO2 partical studded in the crystal.

纳米掺杂等离子喷涂AI2O3/ZrO2涂层的微观组织形貌复杂，存在着纳米柱状晶薄壳内包裹着微米级柱状晶、未熔化的ZrO2陶瓷粒子嵌镶在晶体内部的独特晶内结构。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。