查询词典 under pressure

Any product can't molding a same thickness. Usually the deeper section may sink mark . To prevent this defect it should set holding pressure, The injection speed of holding pressure step is slow but holding pressure settingwithin 25-80% depending on sink mark.

任何产品都不同程度的存在一个厚薄不一的问题，正常情况下，较厚的部分都可能存在一个收缩凹陷的现象，为了解决这种现象，就应应用到保压，保压一般来讲都应用较慢的射速，而压力的设置则应看缩水的情况如何，小到25%，大到80%都有可能。

Any product can't molding a same thickness. Usually the deeper section may sink mark . To prevent this defect it should set holding pressure, The ※※※※ ction speed of holding pressure step is slow but holding pressure setting within 25-80% depending on sink mark.

任何产品都不同程度的存在一个厚薄不一的问题，正常情况下，较厚的部分都可能存在一个收缩凹陷的现象，为了解决这种现象，就应应用到保压，保压一般来讲都应用较慢的射速，而压力的设置则应看缩水的情况如何，小到25%，大到80%都有可能。

Any product can't molding a same thickness. Usually the deeper section may sink mark . To preent this defect it should set holding pressure, The injection speed of holding pressure step is slow but holding pressure setting within 25-80% depending on sink mark.

任何产品都不同程度的存在一个厚薄不一的问题，正常情况下，较厚的部分都可能存在一个收缩凹陷的现象，为了解决这种现象，就应应用到保压，保压一般来讲都应用较慢的射速，而压力的设置则应看缩水的情况如何，小到25%，大到80%都有可能。

CY-100is a mechanical differential pressure indicator.The device can indicate the input of strainer,segregator,valve,pump etc.,and output the pressure difference.It is especially suited foe indicating the jam-up of the filer elements in gas pressure regulating station.It allows the filer element cleaned or replaced in time and running safely and economically.

CY-100型是一种机械式差压指示器，用于指示过滤器，分离器，阀门，泵等设备输入，输出二端压力差异，尤其适用于指示燃气调压计量站上滤芯式过滤器的阻塞程度，便于及时清理或更换滤芯，保证设备安全、经济地运行。

Valve closed, the sealing surface can only rely on media pressure to seal, that is, to rely on media pressure to ram pressure to the other side of the sealing surface of the seat to ensure the sealing surface of the seal, which is self-sealing.

闸阀关闭时，密封面可以只依靠介质压力来密封，即依靠介质压力将闸板的密封面压向另一侧的阀座来保证密封面的密封，这就是自密封。

Valve closed, sealing surface can only rely on Rising Stem Resilient Seated Gate Valve media pressure to seal, in which the medium pressure to ram pressure to the other side of the sealing surface of the valve seat to ensure the sealing surface of the seal, which is a self-sealing.

闸阀关闭时，密封面可以只依靠介质压力来密封，即依靠介质压力将闸板的密封面压向另一侧的阀座来保证密封面的密封，这就是自密封。

Our factory specialized production: Each kind of automobile, barometric pressure, hydraulic pressure hose unit steel pipe unit, each kind of project mechanical hydraulic pressure hose, steel pipe unit, semitrailer, nylon coil unit, each kind of harvester hydraulic pipe and attachment body, each kind of large-scale, medium and small-scale tractor pipeline.

我们厂专业生产：各种汽车、气压、液压软管总成钢管总成，各种工程机械液压软管、钢管总成、半挂车、尼龙螺形管总成，各种收割机液压管及接头体，各种大、中、小型拖拉机管路。

Using high speed photograph and laser shadowgraph method, the effect of opening pressure of injection nozzle, environment pressure and injection orifice diameter on spray characteristics of dimethyl ether are studied by using a pressure bomb, and are compared with those of diesel.

采用高速摄影和激光阴影法在压力容弹中研究了喷油嘴启喷压力、环境介质的密度、喷孔直径等参数对二甲醚喷雾特性的影响，并与柴油的喷雾特性进行了对比。

The results show that the amorphous PLGA fiber with porous structure (0.1-1.0 μm) is obtained by diluted solvent spinning method and the mechanical properties is affected by pressure and temperature. Bending strength and shearing strength of the samples increase firstly and then decrease with the increase of molding temperature and pressure. While the molding temperature is 160℃and the pressure is 105MPa, the PLGA materials possess optimal mechanical properties, bending strength, shearing strength and bending modulus 187.3 MPa, 100.0 MPa and 2.5 GPa, respectively. The mild temperature molding PLGA materials are desired to play a grate role in non-bearing internal fixation devices.

研究结果表明：非晶多孔结构的PLGA纤维可通过溶液沉析纺丝的方法获得，其孔径为0.1~1.0μm；压制压力和压制温度对材料的力学性能影响较大，材料的抗弯强度、剪切强度和抗弯模量均随着温度和压力的增大而先增大后降低；在压制压力为105MPa，压制温度为160℃时，试样的力学性能比较理想，此时，其抗弯强度可达到187.3MPa，剪切强度达到100.1MPa，抗弯模量达到2.5GPa，可望作为非承重部位骨折愈合内固定材料。

It was observed in this pressure range that sodalite underwent a phase transition at about 3 GPa and that the d- 222 value showed an abnormal increase when the pressure was higher than 6.3 GPa. The experimental results are explained on the basis of the pressure effects upon the cage and tunnel structures in sodalite.

对方钠石在高压下相变以及d222增大的原因进行了分析，认为方钠石结构中存在着充填大阳离子的多面体笼和孔道，高压下这些笼和孔道容易扭曲变形，从而造成结构的改变。

More direct, directer ; most direct, directest

径直的，笔直的

Do you know how to use a chain saw?

你知道如何使用链锯吗？