查询词典 under load

After the biomechanical finite element analysis for the three-dimensional reconstruction model, we find the structure of the deformed nose showes the following characteristics: 1, Nasal septum, nasal columella, lateral feet of nasal alar, lateral nasal dorsum are stress concentrated regions, that is the key mechanical positions of deformed nose; 2, Under the static state, nasal deformation has a very small value of stress distribution, under displacement load status, the deformed nasal has a large value of the stress distribution; 3, Ipsilateral nasal columella are the the key mechanical parts of deformed nasal rectify. And lateral nasal alar is also the most stress concentrated areas.

对于重建后的单侧唇裂鼻畸形鼻部模型进行有限元生物力学研究，发现畸形鼻的力学结构呈现以下特点：1、鼻中隔、鼻小柱、鼻翼外侧脚、鼻背外侧是单侧唇裂鼻畸形应力分布的集中部位，也就是畸形鼻部的力学关键部位；2、在静态状态下，畸形鼻部拥有的应力分布值很小，在位移载荷状态下，形变后的畸形鼻部拥有的较大的应力分布值；3、单侧唇裂鼻畸形整复中，鼻小柱患侧部是畸形整复的力学关键部位，其次就是患侧鼻翼部。

Under low stress repeated impact load, the plastic deformation of materials is epistrophe which is mainly in the range of 2mm under surface.

材料在低应力多冲条件下的塑性变形表现出"趋表"的特点，塑性变形主要集中在表面以下2mm左右的区域。

Decrements in BSFC are more than 11% and 20% under the full load and part-load conditions respectively.

应用该系统研究了涡流比对发动机性能的影响，结果表明，涡流比在1.0左右最佳。

Fig.4 shows the speed response of the motor under no-load and full-load conditions for a change in the desired speed from 700 r/min to 1600 r/min aid back to 700 rimin.

图4显示了在预期的速度从700改变电机的转速响应/分至1600转/分回700 rimin.Fig援助下空载和满载条件。

Most gasifiers with quenching process have the problem of carrying water in the quenching chamber, which is more obvious under high load conditions constraining the increase of the gasifier load.

采用激冷流程工艺的气化炉，大都存在着激冷室带水的共性问题，且在高负荷生产状况下尤为明显，直接制约了气化炉负荷的提高。

To adopt finite meta method analyzes stress strain action of Al-plastic compound pipe under Analog load status and studies the influence of load capacity by variation of diameter of medium Al layer and change of joint part length lap joints.

采用有限元方法分析了铝塑复合管在模拟承载状态下的应力应变行为，研究了中间铝层的直径变化以及搭接接头搭接部分长度的变化对承载行为的影响。

Depending on the general solution of the vibration of system given in the front, considerate that the nature wind is always in a gust form, model the load of wind on the canopy and trunk of tree as a impulse load on the free end of the staff, and gets the responses of vibration under these conditions, then picture the curve of the vibration.

根据之前得到的系统振动通解，考虑自然风多呈阵风形式的影响，将作用在树冠和树干上的风载简化为作用在弹性杆自由端质量团处的脉动载荷，进而分析并得到此条件下杆的振动响应，绘出此情况下杆的振动响应曲线。

Proposes a method for selecting optimal chiller unit configuration in design phase, in which the energy consumption of chillers is simplified to the function of actual cooling capacity and entering water temperature of the condenser, then the all-year building load frequency distribution under different outdoor wet-bulb temperature that determines the minimum entering cooling water temperature is obtained by dynamic load calculation, and finally, calculates the all-year energy consumption and energy consump...

提出一种在设计阶段对冷水机组方案进行优化配置的方法。首先，冷水机组的能耗计算简化为制冷机的实际制冷量和冷却水进口温度两个独立变量的函数。进一步，通过建筑动态负荷计算获得全年冷负荷频率特性以及相应的室外湿球温度分布，其中湿球温度决定了冷却水最低进口温度。最终，计算出各种冷水机组配置方案的全年以及不同冷负荷需求工况下的运行电耗，并得出最优化的节能方案。

It can be used to simulate a heavy load on a server, network or object to test its strength or to analyze overall performance under different load types.

它可以用于模拟服务器或网络上的高负载，或者是测试其长度的对象，可以分析不同加载类型之间的综合性能。

In this paper, test research have been performed on the two important mechanical properties indicator compressive modulus of elasticity and shear modulus. Numerical simulation has been performed on the base of results of test under the situation uniform and uneven thickness of elastomer layer, which analyze internal stress distribution of the elastomeric bearing, as follows:(1) The traditional test methods of compressive modulus of elasticity test are rather cumbersome and take up experimentalists lots of time. This paper has improved the traditional test methods of compressive modulus of elasticity test, which has collected the holding-load time together to concentrate on holding load. The tests have been performed on different types of bearings, which results show that the results of the improved test method conform to the error range regulated by the standard and can effectively save time for the experimentalists, also eliminate the accumulative error.

本文主要对板式橡胶支座的抗压弹性模量、抗剪弹性模量两个重要力学性能指标进行试验研究，并在试验结果的基础上对均匀胶层厚度和不均匀胶层厚度两种情况进行数值模拟，分析橡胶支座内部应力分布规律，具体内容如下：(1)传统抗压弹性模量试验方法比较繁琐，占用试验人员大量时间，本文对传统抗压弹性模量试验方法进行了改进，将持荷时间集中起来进行集中持荷，通过对不同类型支座进行试验，试验结果表明该改进试验方法所得结果符合标准规定误差范围，为试验人员节省了大量时间，并且还消除了传统方法中的累计误差。

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。