查询词典 turning point or barrier

Since the day last week when I first read your poems, I quite laugh to remember how I have been turning and turning again in my mind what I should be able to tell you of their effect upon me, for in the first flush of delight I thought I would this once get out of my habit of purely passive enjoyment, when I do really enjoy, and thoroughly justify my admiration— perhaps even, as a loyal fellow craftsman should, try and find fault and do you some little good to be proud of hereafter!

一个星期前的今天，我第一次读到你的诗篇，然后就一直在反复琢磨，能对你谈点什么感受，现在想起这件事，仍不免哑然失笑。当时，我心里感到一阵狂喜，想道：这次我要打破以前的旧习，不能像平时真正欣赏一首诗那样，只是单纯而被动地享受，而要清楚地说出自己欣赏的理由来——我也许会像一个忠实的同行应做的那样，试着挑出些毛病来，以期对你有所助益，尽到一个忠实的同行应尽的责任，日后也好感到脸上有光啊！

The pick_up and analyse for parts data have been made and craftwork decision has been made. Profile calculations for turning parts and islands and islets for milling parts problem in mould cavity have been especially made. Post process for turning parts and milling parts have been realized. The cutter locus file has been made.

通过对零件数据的提取、分析及工艺决策，深入研究了车削类零件的轮廓计算和铣削类零件型腔中岛屿问题的处理方法，实现了车削、铣削零件的前置处理，形成刀位文件，并生成了相应的零件工艺卡。

Finish-cut turning, fine boring, finish-turning, finish-milling, shave-planing, fine machining of hardened steel, abrasive materials, hard and grey cast iron, Si-Al-metals, plastics, electrode carbon, etc.

对硬钢、耐磨料、硬铸铁、灰铸铁、硅铝合金、塑料、炭精棒等进行精密车削、精细镗孔、精细铣削、刨平、等的精细机械加工。

RKX Finish-cut turning, fine boring, finish-turning, finish-milling, shave-planing, fine machining of hardened steel, abrasive materials, hard and grey cast iron, Si-Al-metals, plastics, electrode carbon, etc.

对硬钢、耐磨料、硬铸铁、灰铸铁、硅铝合金、塑料、炭精棒等进行精密车削、精细镗孔、精细铣削、刨平、等的精细机械加工。

Put a boiled egg on the table rotation, if the force fit, it will be erected Turning turning up, The raw egg will not.

答：把煮熟的桌子上旋转鸡蛋，如果合适的力量，将竖立转着转时，该生鸡蛋会不。

In the process of development and rebuilding of hermeneutics, there are two important turnings -the turning of ontology and the turning of practical philosophy, which have the significance of revolution and creation.

解释学揭示的是人类精神活动中&理解&的问题，其发展几易其貌，过程中历经两次革命性和创造性的转向——本体论转向和实践哲学转向。

The grain-leaf ratio showed a periodic oscillation relation to total seedling number in each growing stage, it was decreased with the increasing of total seedling number in earlier winter stage, wintering stage and jointing stage and was increased with the increasing of total seedling number in turning green stage. The grain-leaf ratio was bigger when the total seedling number was 2700000-3200000 plants/hm^2 in earlier winter stage and was 6400000-8200000 plants/hm^2 in turning green stage.

粒叶比与各生育阶段总苗数呈周期性振荡关系，且随着冬前期、越冬期和拔节期总苗数的增加而减小，随着返青期总苗数的增加而增大，当冬前期总苗数在270万320万株／hm^2、返青期总苗数在640万820万株／hm^2时，粒叶比较高。

On the research of refloating engineering calculation model, the present absent calculation method of stranded ships turning and refloating resistance was mostly lucubrated, the calculation formula of stranded ships turning and refloating resistance was deduced.

在脱浅工程计算模型研究方面，重点对现行脱浅工程计算方法中缺少的搁浅舰船转向与出浅阻力计算方法进行了深入研究，推导出了难船转向与出浅时阻力计算公式。

The fitting of the Turning Gear is normal, and the electric current value is within the range of the standard value when the turning motor is run.

盘车机工作正常，转车马达运转时其电路值应保持在标准范围内。

A The fitting of the Turning Gear is normal, and the electric current value is within the range of the standard value when the turning motor is run.

盘车机工作正常，转车马达运转时其电路值应保持在标准范围内。

Nowadays, most of research are to build a transmutative Petri Nets through adding controlling place sets, controlling arc sets and controlling policy to the basic Petri Nets, while the Controlled Petri Nets could be used to argue many controlling theory problems conveniently and to induce many logically and physically supervisory and solve the Event Feedback Controlling Problems and State Feedback Controlling Problem in DEDS supervisory theory.

目前大多数的研究表现为在变形后的受控Petri网基础上，利用各种方法求得各种逻辑型、结构型控制器，解决DEDS监控理论中的事件反馈控制问题与状态反馈控制问题。

On one hand, there are discussions with the works council and union about extension of short time working up to the end of September.

一方面，有讨论，工程理事会和联盟关于延长工作时间短至9月底。