查询词典 torsional

Methods 15 cases of torsional strabismus were studied and were treated with the superior obliques sagittal transposition according to examination results of occular movements, amblyoscope,double Modaox rod bar and fundus photograph.

对15例旋转斜视患者根据眼球运动、同视机、双马氏杆和眼底照相等检查，行上斜肌矢状移位术。

Methods 15 cases of torsional strabismus were studied and were treated with the superior obliques sagittal transposition according to examination results of occular movements, amblyoscope,double Modaox rod bar and fundus photograph.

对15例旋转斜视患者根据眼球运动、同视机、双马氏杆和眼底照像等检查，行上斜肌矢状移位术。

On strength computation,the finite element models of rotating mirror were established according to the real structure of the mirror,and the rotating three-faced beryllium mirror were analysed.Results display that the surface deformation magnitude of the mirror is approximately 0.334 6 μm,and the maximum stress is 0.204 GPa at 600 m/s of edge linear speeed.The regions of maximum stress are on the axial hole and symmetric to symmetrical planes of mirror body,and keep beelines to surfaces.On the modal analysis,the results show that the first and second modals of bending vibration exist around 3.4×105 r/min and 6.6×105 r/min,which appear binate and orthogonal respectively,and another modal belongs to the first torsional vibration that occurs by 5.13×105 r/min.

运用该方法得出转镜镜面变形量、内部应力分布和振动模态参量的定量数值：在边缘线速度600 m/s下，三面体铍转镜的最大变形量为约0.334 6 μm；最大应力0.204 GPa，位于轴孔附近并与镜面距离最短处；两个在互相垂直平面内的一阶弯曲振动模态发生在3.4×105 r/min附近，一阶扭振点位于5.13×105 r/min附近，两个二阶弯曲振动点位于6.6×105 r/min附近。

The curve continual steel box Liang shearing force stagnates the effect finite element analysis box section Liang has the big flexural rigidity and torsional stiffness, the stress performance good, spanning ability big, on the bridge the field of vision open and so on the merits, is in the bridge design the commonly used structural style, when receives under the dead load or the symmetrical live load function winding, because the lifting surface detrusion causes its bending stress to present the non-uniform distribution condition along the Liang width direction, this phenomenon is called "the shearing force to stagnate the effect".

曲线连续钢箱梁剪力滞效应的有限元分析箱形截面梁具有较大的抗弯刚度和抗扭刚度、受力性能好、跨越能力大、桥上视野开阔等优点，是桥梁设计中常用的结构形式，在受恒载或对称活荷载作用下挠曲时，由于翼板的剪切变形致使其弯曲应力沿梁宽度方向呈现不均匀分布状态，此现象称为&剪力滞效应&。

Erenow, it has not been found that the application was reported in which the multivariable model was identified and both bending and torsional modes were depressed.

在此之前，并未见到针对柔性结构建立多变量辨识模型，对弯曲和扭转模态都进行抑制的实际应用的例子。

A portable torsional vane shear device has been developed to meet the needs of research work in marine geology, river exploration, geotechnics, oil drilling and soil mechanics.

鉴于海洋地质、内河勘察、地下工程、石油钻探以及土壤研究的需要，我们借鉴国外仪器的特点设计了袖珍十字板剪力仪。

Nylon shanks in the Pagoras provide torsional rigidity and support, and grippy outsoles give you traction on dirt and rocks.

Nylon shanks in the pagoras提供抗扭刚度和支持，grippy outsoles技术对泥土和石块拥有更好的抓地力。

The experiment carried out on flexible rotor test bench for torsional vibration measurement shows that the DK-Ⅲ instrument is able to accomplish hish precise measurement.

在挠性转子实验台上的扭振测量实验表明，DK.III型扭振测量仪可实现轴系扭振的较高精度测量。

In this article, data were collected from the Chiba dense array, which consists of 44 accelerometers with interstation spacing in the range of 5 300 m that are employed to estimate the torsional ground motion.

为了估算扭转地震动，日本在千叶地区布设了拥有44台加速度计的千叶密集台网，台际空间范围为5 - 300 m 。本文使用此密集台网的记录数据。

The glass transition temperatures of the o-CFER/DDE isothermally cured partially are determined by means of torsional braid analysis, and the results show that Tg increased with conversion.

用动态力学谱仪测定了o-CFER/DDE 体系在不同固化程度下的玻璃化转变温度，结果表明固化体系的玻璃化温度随反应程度的增加而升高。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐