查询词典 torsional stress

If the instrument is subjected to torsional loads, the shear stress at every cross section is proportional to the torque and the radical distance from the bars axis, and is inverse proportional to the polar moment of inertia of the cross section.

扭转载荷下，横截面某点的切应力与扭距成正比，与到截面中心的距离也成正比，与横截面的极惯性距成反比。

This resulted in the twisting and fracturing of the leads. Torsional displacement of and tissue stress on subauricular lead connectors caused early discomfort in that region.

放置心脏起搏器和除颤器的类似成功经验显示：通过患者有意识的或者下意识的对皮肤装置进行操作，可能导致动作电位源自发或更频繁的迁移和中断。

By applying one couple of unit force on two suspension centers based on 3D FEM to calculate their relative displacement, coefficient of torsion displacement, the radial gate s torsional rigidity coefficient is derived; and its stress distribution is analyzed to solve radial gate s torsion problem.

基于空间有限单元法，对闸门吊点施加1对单位力计算出2个吊点的相对位移———闸门扭转挠度系数，进而推算出闸门抗扭刚度系数和单位位移下的应力状态，据此最终解决弧门的扭转问题。并通过某一工程实例的分析计算，表明该方法在生产设计中具有较好的实用性，可以有效地解决弧形闸门的扭转计算问题

The calculating accuracy is ensured by expelling oddity points from the results. In part four, rotor life-loss caused by shear stress under torsional moment, turbo-generator rotors' combined vibration of bending and torsion are studied, and the maximum shear stresses of a stimulate rotor of N300MW steam turbine are calculated.

在第3章，重点研究了汽轮发电机组转子扭振机理和数学模型，特别是汽轮机特殊结构的模化方法，编写了计算程序，计算了某型300MW汽轮发电机组转子和试验台转子扭振特性。

Based on the fatigue test results of SAE 1045 medium carbon steel,the multi-axial fatigue life predication models for different ratios of torsional nominal stress amplitude to the axial one are studied respectively.

基于SAE 1045中碳钢的单-多轴疲劳试验结果，在研究了扭转名义应力幅与拉伸名义应力幅不同比值时的多轴疲劳寿命预测模型之后，建立了统一的多轴疲劳寿命预测模型。

It is found that the shear stress in the torsional bar is much higher than that in the main shaft except blowing operation.

发现了除吹炼工况外扭力杆剪应力明显高于耳轴剪应力等现象。

The influence of the defect on the torsional stiffness and the stress distribution are calculated and analyzed by finite element method. The defect widths range from one-tenth of the femur outer diameter(0.1D) to (0.3D), and defect lengths range from 1D to 5D.

计算结果表明：骨缺损长度为D时，对股骨扭转刚度和剪应力分布的影响较小；骨缺损长度从2D增至4D时扭转刚度急剧减小，而且剪应力的最大值位于骨缺损中心。

The curve continual steel box Liang shearing force stagnates the effect finite element analysis box section Liang has the big flexural rigidity and torsional stiffness, the stress performance good, spanning ability big, on the bridge the field of vision open and so on the merits, is in the bridge design the commonly used structural style, when receives under the dead load or the symmetrical live load function winding, because the lifting surface detrusion causes its bending stress to present the non-uniform distribution condition along the Liang width direction, this phenomenon is called "the shearing force to stagnate the effect".

曲线连续钢箱梁剪力滞效应的有限元分析箱形截面梁具有较大的抗弯刚度和抗扭刚度、受力性能好、跨越能力大、桥上视野开阔等优点，是桥梁设计中常用的结构形式，在受恒载或对称活荷载作用下挠曲时，由于翼板的剪切变形致使其弯曲应力沿梁宽度方向呈现不均匀分布状态，此现象称为&剪力滞效应&。

The stress in tower type of derrick is smaller than the other types of derricks under the combined action of compressive and torsional loads.

与仅受压载荷相比，井架承受压扭联合载荷时，弦杆应力稍有增加，而非弦杆应力有较大的增加。

The analysis shows that, blade vibration and torsional deformation is the mainly manifestations of the cutting mechanism head body ,the maximum deformation of the helical blade is 18.01mm, the maximum stress value in the welding of corner ,connection of end disk and helical blade is the weak link, helical blade is the main component, which effects the dynamic characteristics of cutting mechanism head body.

所得结论对于改进螺旋钻采煤机截割机构头体的设计、提高其动态性能和使用寿命具有一定的指导意义和参考价值。2、文章中部分措词需要修改，摘要翻译中文化，论文整体格式需要修改。3、数值模拟的约束条件有待商榷，对于结果应该对比实际试验和有关材料特性表，更有说服力。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。