查询词典 torsional stress

The stress concentration factor and stress intensity factor of annularly notched shaft subjected to torsional load were given.

给出扭转载荷下环形缺口的应力集中系数和环形裂纹的应力强度因子。

It was found that: the failure form of the stubble will be splitting and breaking when the stalk is cut by single blade; And it will be axial direction crack by torsional shearing stress, splitting and breaking by bending stress when the stalk is cut by two or more blades one by one.

结果表明：甘蔗茎秆受一刀切割时，根茬破坏的模式有劈裂和弯曲断裂；受两刀或多刀切割时根茬破坏模式有因扭转而产生的纵向裂纹，因弯曲而产生的劈裂和弯曲断裂。

Due to the effect of torsional vibration arose by eccentricity of the center of mass and the center of rigidity, there will produce stress concentricity in some local location of the structure, which is very detrimentally. This paper discussed the contribution of the reduction of the response of torsional vibration of the accessorial eccentrically braces in structure on emphasis.

由于不规则高层建筑的质心刚心偏心而引起的扭转振动效应，会使结构的局部产生应力集中等极为不利的情况，因而本文着重讨论了增设偏心支撑后的结构，对减小原结构的扭转振动效应的贡献。

The soil static and dynamic universal triaxial and torsional shear apparatus which can simulate the cyclic stress characteristic of sand on seabed is used to perform experimental tests of loose carbonate sand s with a relative density of 30% subjected to vertical-and-torsional coupling cyclic shear with the rotation of principal stress axes induced by ocean wave.

利用土工静力-动力液压三轴-扭剪多功能剪切仪模拟海洋波浪的加载形式，对相对密度为30%的钙质砂进行了扭转和竖向耦合循环剪切试验，着重研究了复杂应力状态下初始主应力方向角α0和中主应力系数b对钙质砂动强度特性的影响。

Working conditions of drilling string is complex underground, various factors ofteninteract, in the process of drilling, drilling string acts complex movement in drill fluid, drillfluid unavoidable corrupt drilling string because such as oxygen, hydrogen sulfide and manysalts are dissolved in it. At the same time, many cyclic stresses act on drilling pipe, such asflexural cyclic stress, torsional cyclic stress.

钻柱在井下的工作状态是复杂的，常常是多种因素交织在一起的，在钻井过程中，钻柱在溶解了氧、硫化氢及各种盐类的钻井液中作复杂运动，不可避免的受到它们的腐蚀作用，同时还要受到弯曲、扭转等交变应力作用。

METHODS: The endodontic instrument was assumed as a metal conical bar. The normal stress of bending loads and the shear stress of torsional loads were calculated with the knowledge of mechanics. The relations between stress and such parameters as angle and radius of canal curvature, radius of instrument, polar moment of inertia, and metal elastic modulus were analyzed. The criteria for yielding and fracture of the instrument were discussed.

将根管器械刃部假设截面为圆的金属细锥杆，利用材料力学及断裂力学的原理与方法，分别计算根管器械在弯、扭载荷下的应力分布，分析应力与根管弯曲角度、根管弯曲半径、器械直径、器械横截面极惯性距、金属弹性模量等参数的确切关系；探讨器械屈服、断裂失效的准则。

METHODS: The endodontic instrument was assumed as a metal conical bar, the normal stress of bending loads and the shear stress of torsional loads were calculated with the knowledge of mechanics , the relations between stress and such parameters as angle and radius of canal curvature, radius of instrument, polar moment of inertia, metal elastic modulus were analyzed, the criteria for yielding and fracture of the instrument were discussed .

将根管器械刃部假设为截面为圆的金属细锥杆，利用材料力学及断裂力学的原理与方法，分别计算根管器械在弯、扭载荷下的应力分布，分析应力与根管弯曲角度、根管弯曲半径、器械直径、器械横截面极惯性距、金属弹性模量等参数的确切关系；探讨器械屈服、断裂失效的准则。

The torsion resistance of the tension bar and the calculatiolls of bending shear stress, free torsional shearstress and bending torsional shear stress on the section are also discussed.

对冷弯槽钢单侧挂板墙梁的受力性能进行了分析，讨论了墙梁间拉条对截面抗担所起的作用，以及综合考虑弯曲剪应力、自由扭转剪应力、弯曲扭转剪应力的剪应力计算。

The distribution of gear's contact stress, root stress, and contact engagement line in the engagement situation of gear pairs, were obtained on the base of explicit integration method. 3. Adopting the method of system matrix, the torsional vibration differential equation of general shafting was gained. The simple harmonic forms of excitation torque under the normal combustion or piston flameout of in-line engine and v-type engine were analysed. The decoupled algorithm of free vibration and forced vibration and the solution to the vibration damper's energy of resistance and the off-resonance calculation were studied. The sensitivity formulations of the natural frequency and vibration mode to physical parameters of system were derived by solving the eigenvalue problem. These sensitivity formulations provided the theoretical base for the dynamic modification of structure.

运用系统矩阵法建立了轴系的扭振微分方程，并对直列和V型发动机在正常发火和气缸熄火工况下的激振力矩进行了详细的简谐分析；基于精确方法推导了自由振动和强迫振动的解耦算法，给出了能量法计算中的减振器阻尼功求解和非共振计算方法；并研究了曲轴系扭振非线性分析中的变惯量问题，得到了单缸转动惯量的精确求解公式以及变惯量和固有频率的关系式；最后，从特征方程和振型正交性出发，推导了固有频率和振型对轴系转动惯量和刚度等物理参数的灵敏度，为扭振系统的结构动力学修改提供了理论基础。

On strength computation,the finite element models of rotating mirror were established according to the real structure of the mirror,and the rotating three-faced beryllium mirror were analysed.Results display that the surface deformation magnitude of the mirror is approximately 0.334 6 μm,and the maximum stress is 0.204 GPa at 600 m/s of edge linear speeed.The regions of maximum stress are on the axial hole and symmetric to symmetrical planes of mirror body,and keep beelines to surfaces.On the modal analysis,the results show that the first and second modals of bending vibration exist around 3.4×105 r/min and 6.6×105 r/min,which appear binate and orthogonal respectively,and another modal belongs to the first torsional vibration that occurs by 5.13×105 r/min.

运用该方法得出转镜镜面变形量、内部应力分布和振动模态参量的定量数值：在边缘线速度600 m/s下，三面体铍转镜的最大变形量为约0.334 6 μm；最大应力0.204 GPa，位于轴孔附近并与镜面距离最短处；两个在互相垂直平面内的一阶弯曲振动模态发生在3.4×105 r/min附近，一阶扭振点位于5.13×105 r/min附近，两个二阶弯曲振动点位于6.6×105 r/min附近。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。