查询词典 top liner

The application of mineral fiber as a filler in coater in white board top liner is discussed.

矿物纤维对面浆加填后，能够达到降低成本，提高不透明度，提高遮盖力的目的。

At the wind tunner blocking joint, set ramrod rib reinforcement as well as strengthening liner iron from above to the bottom; fix a bracing sheet on the top; joint between wind tunner blocking adopts flanging butt joint, no lacing wire on the wind tunner top, fabricate strictly according to GB7190.2 - 97 standard.

风筒分块连接处，设置从上至下通条加强筋以及加强衬铁；上部作一圈加强板；风筒分块间联接采用翻边对接，风筒上部不设拉筋，严格按照GB7190.2-97标准制造。

The M.E. No.6 cyl. exhaust valve head was found broken and fell into the cylinder and thus the cylinder head was seriously damaged, the cyl. liner top pitted and the piston top pierced.

凹痕，成麻点状 pitted 如：主机第 6 缸排气阀头破裂，跌落到汽缸内，造成汽缸头严重损坏，汽缸套顶部呈凹痕，活塞顶部被刺穿。

The M.E. No.6 cyl. exhaust valve head was found broken and fell into the cylinder and thus the cylinder head was seriously damaged, the cyl. liner top pitted and the piston top pierced.

凹痕， pitted 凹痕，成麻点状如：主机第 6 缸排气阀头破裂，跌落到汽缸内，造成汽缸头严重损坏，汽缸套顶部呈凹痕凹痕，凹痕活塞顶部被刺穿。

Cylinder, the cylinder sets of radial a surplus deformation of the cylinder sets a great impact on the cylinder liner reduced radial a surplus amount to reduce the deformation of the cylinder sets, the top surface of the body decreases roughness, but it will increase the body on the plane cylinder only mouth the roughness ; Preload reduced cylinder head bolt deformation of the cylinder liner little effect, the body can reduce the top surface roughness and cylinder body on the plane I ended roughness; Shen appropriate reduced cylinder head bolt hole deep can reduce the deformation of the cylinder sets, but will cause the body and the top surface roughness on the cylinder body only I roughness increases Plane .

工作工况下，对于第2缸来说，气缸套径向过盈量对气缸套变形影响很大，减小气缸套径向过盈量，有利于减小气缸套的变形，减小机体顶面不平度，但会增大机体上缸套止口平面的不平度；减小缸盖螺栓预紧力对气缸套变形影响很小，可减小机体顶面不平度和机体上缸套止口平面的不平度；适当减小缸盖螺栓沉孔深可以减小气缸套的变形，但会造成机体顶面不平度和机体上缸套止口平面不平度的增大。

In this paper, two kinds of material model were introduced, based on the same condition, such as explosive, liner structure, Johnson-Cook and Steinberg model were selected for liner. The process of shaped charge jet penetration into target was simulated using ANSYS/LS-DYNA, the results compared and showed that these two kinds of model can simulate the form and penetration process of the jet accurately, and the top velocity of the jet head were almost the same.

本文介绍了两种材料模型，在炸药、药型罩结构等条件相同的情况下，药型罩选择Johnson-Cook与Steinberg两种材料模型，利用ANSYS/LS-DYNA软件对聚能射流侵彻靶板进行模拟仿真，对比仿真结果，得出两种模型都能很好的模拟射流的形成及侵彻过程，且各时刻射流头部最高速度差值很小。

Using Frovi as the top liner ensures that we can supply wine boxes that are significantly stronger than many offered by our competitors.

使用弗勒维为炉顶确保我们能够提供葡萄酒框明显强于我们的竞争对手提供了许多。

In order to understand better the process of hydrocarbon formation and the effect of the top land crevice and the oil layer of the cylinder liner on unburned hydrocarbons during cold start and idling period,the temperature of piston top land and liner has been measured.

为了更好地弄清起动和怠速时发动机缸内未燃碳氢生成过程以及顶岸间隙和油膜对缸内未燃碳氢的影响，测量了起动和怠速过程活塞顶岸壁面和缸套壁面温度。根据测量结果，预测了起动过程顶岸间隙和壁面油膜处未燃碳氢生成量，发现顶岸和缸套壁温在发动机起动后（150～200）s时达到其稳定状态。

The Fit Plus Liner name was created to reflect the engineered fit of the sock (it stays fitted to the foot where others tend to slip away into the shoe), the plus factor of its superior craftsmanship and optimised freshness and the fact that it's a sock liner made from top quality cotton.

适合加衬垫的名称是为了反映袜子设计适合（它停留安装在脚下别人往往渗入鞋以外），其卓越的工艺和优化的新鲜度和的事实，是一个多因素袜子从优质棉衬垫。

Combining with the characters of liner industry, the paper set up an evaluation index system. And then 15 liner corporations picked out from top 20s in container liner industry were evaluated synthetically with catastrophe progression method and set pair identical degree analysis method. Based the above evaluation, a contrast analysis between the core competence of the container liner corporation in our country and ones in other countries was conducted.

在此基础上，本文在全球运力排名前20位的大型集装箱班轮企业中选取了15家为研究对象，结合国际集装箱班轮运输业的行业特征，建立了核心竞争力评价指标体系，挑选了突变模糊隶属函数法和集对同一度分析法两种方法，对研究对象的核心竞争力进行了综合评价，并对结果做出了分析，同时，借助于核心竞争力评价指标体系，对我国集装箱班轮企业的核心竞争力状况进行了对比分析。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。