查询词典 tooth wheel

The interference between the tooth surface of the worm and the grinding wheel will occur under certain conditions of grinding wheel diameter and setting parameters, which will lead to the overcut of the tooth surface.

在一定的砂轮直径及安装参数下磨齿时砂轮和蜗杆的齿面将产生干涉，致使蜗杆齿面发生过切。

After the low load capacity reason of the sprocket wheel was analyzed, the methods of increasing the load capacity were given from three ways: determining the structure of the rolling wheel, choosing the pressure angle of the tooth sharp and decreasing the friction of the tooth face.

分析了星轮承载能力低的原因，并从辊轮结构的确定、齿形压力角的选择、齿面摩擦的降低等三方面给出了提高星轮齿面承载能力的措施。

In the paper,the transmission of designed roller oscillating tooth reduction gear adopts osci llating tooth gear drive without exception,one-stage reduction gear and two-stage reduction gear have joined through spline coupling band;The joining way of shock wave thellomble and oscillating tooth adopts the biserial bearing of without inner ring of needle bearing,and directly adopts bearing outer ring as shock wave thellomble;Center wheel of two-stage reduction gear and center wheel of two-stage reduction gear passes through taper thread,and center wheel is fixed;As soon as the flange of input end and center wheel of one-stage reduction gear,the flange of export end and center wheel of two-stage reduction gear makes monobloc structure.

本文预设的井下减速器的传动均采用活齿传动，一级减速器的输出轴和二级减速器的输入轴通过花键联轴套联接；激波环与活齿的毗连方式采用能蒙受较大载荷的无内圈双列滚针不锈钢管，且直接采用不锈钢管外圈作为激波环；一级减速器的中心轮和二级减速器的中心轮是通过锥螺纹毗连的，且中心轮固定；一级减速器的中心轮与输入端的法兰盘，二级减速器的中心轮与输出端的法兰盘均做成整体的结构。

In the paper,the transmission of designed roller oscillating tooth reduction gear adopts oscillating tooth gear drive without exception,one-stage reduction gear and two-stage reduction gear have joined through spline coupling band;The joining way of shock wave thimble and oscillating tooth adopts the biserial bearing of without inner ring of needle bearing,and directly adopts bearing outer ring as shock wave thimble;Center wheel of two-stage reduction gear and center wheel of two-stage reduction gear passes through taper thread,and center wheel is fixed;As soon as the flange of input end and center wheel of one-stage reduction gear,the flange of export end and center wheel of two-stage reduction gear makes monobloc structure.

本文设计的井下减速器的传动均采用活齿传动，一级减速器的输出轴和二级减速器的输入轴通过花键联轴套联接；激波环与活齿的连接方式采用能承受较大载荷的无内圈双列滚针中国财经圈，中国财经圈，且直接采用进口中国财经圈外圈作为激波环；一级减速器的中心轮和二级减速器的中心轮是通过锥螺纹连接的，且中心轮固定；一级减速器的中心轮与输入端的法兰盘，二级减速器的中心轮与输出端的法兰盘均做成整体的结构。

Lack tooth count gear wheel parameter optimization design CAD software one to shift little tooth count oblique gear wheel process parameter carry on software that intelligence optimize most.

少齿数齿轮参数最优化设计CAD软件是一款对变位少齿数斜齿轮加工参数进行智能优化的软件。

The components of tooth wheel cover, key and so on that in axis select standard letter by the corresponding number.

而且在设计之中，尽量选用通用件，减少了制造成本，增加了经济效益。

And the effects of the tooth wheel number on the removal efficiency,the COx formation and the energy efficiency were investigated.

采用正极性高压直流供电和串齿线放电极——管式接地极构成的放电等离子体反应器，研究了苯系物去除效率与供电电压之间的关系，以及放电极齿轮数对苯系物去除效率、COx(CO2+CO)生成量和能量效率的影响。

According to the principles of tooth meshing and manufacturing helicoi ds, a mathematics model is constructed to reflect the manufacture process of nut , and the formula of the grinding wheel section is developed. The parameters of the section are obtained through numeral arithmetic; moreover the parameters of the dresser are worked out. Based on these work, the solid model of the ball scr ew nut, grinding wheel and tooth dresser are developed in the Pro/E software, wh at's more, the process of the dressing...

根据螺旋面加工原理、齿形啮合原理及回转面砂轮加工螺母工艺建立了相应的数学模型，并推导出砂轮截形的计算公式；采用数值计算方法求解砂轮截形参数，进一步得到修整器靠模板的参数；在此基础上，利用Pro/E软件对大导程滚珠丝杠螺母、砂轮和砂轮修整器进行了实体建模，并对砂轮的修整过程和螺母的加工过程进行了运动仿真，有效地验证了砂轮截形的计算结果。

Double tooth, the crown tooth, umbrella tooth, wheel, Helical, worm gear, safety gear clutch, kinds of non-standard shaped teeth and plastic gear boxes, precision gear, such as copper.

双层齿、皇冠齿、伞齿、滚轮、斜齿、蜗轮蜗杆、安全离合齿、各种非标异型齿及塑胶齿轮箱、精密铜齿轮等。

Enginering machine part, Gteel Casting, Grey Iron Casting Alominium Casting, Ljner, Link Train, Brake system, China Wheel Bracket TooTH etc.

产品/Product：建筑工程机械的c/n铸钢件、铸铁件、铸铝件、高锰钢型板，产品有连杆、链轮、支架、箱体 LIP TooTH等等。

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。