查询词典 toasting-fork

Stick the fork into the potato.

用叉子叉土豆。

Stick the fork into the potato.

用叉子插土豆。

Study of lateral shocks observed during fork truck and pallet jack operations for the handling of palletized loads.

研究发现，在横向震荡叉车、托盘千斤顶作业处理托盘负荷。

When eating salad, you should use a oon or a fork?

吃沙拉时，你应该用勺还是用叉？

"So all components are based on latest supersport technologies: upside-down front fork, fully adjustable suspensions, Brembo radial brake pump, radial brake calipers, R1-type swingarm, everything."

&因此，所有的组件都基于最新的超级技术：倒置前叉，完全可调悬架，伦博径向制动泵，径向制动卡钳，受体1型swingarm ，一切。&

The main products: geological accessories; drill, drill gear; mud pump, mud pump accessories; and drill pipe, joint locks, consisting mainly of drilling materials, to pull the drill pipe, casing pliers, Bocha, consisting mainly of drilling pad fork Tools; series of geological accessories ......

主要产品：地质配件；钻机，钻机齿轮；泥浆泵，泥浆泵配件；和以钻杆，锁接头，为主的钻探材料；以钻杆钳子，套管钳子，拨叉，垫叉为主的钻探工具；等系列地质配件。。。。。。

For the upper and lower physical decomposition of the fuel pump, pump body can be placed, open side cover, remove the pump head fastening nut, remove the pump head, hand clamp plunger living roots, slowly out the plunger and spring cylinder fault, with clean petrol or diesel repeated washing, wash, after-loading complex (note the plunger into the regulation of regulation must fork arm), and alternately tighten pump head nut, rotating camshaft, oil pump pulled the handle to manipulate the review.

2对于上、下体能分解的喷油泵，可将水泵体平放，打开侧面盖板，卸下泵头紧固螺母，取下泵头，用手钳夹住柱塞根部，慢慢抽出故障缸柱塞和弹簧，用清洁的汽油或柴油反复清洗，洗净后装复(注意柱塞调节臂必须装入调节叉内)，并交替拧紧泵头螺母，转动凸轮轴，扳动油泵操纵手柄复查。

Injector fuel supply or pressure is not enough, atomization bad, drip, etc.; plunger rod adjustable arm or teeth protruding ears from the governor lever fork slot prolapse in non-oil position; fuel pump plunger and barrel assembly seriously wear and tear, oil pressure is too low, the oil valve wear serious Mifengbuyan; washer crack and deformation, a broken valve spring, injector wear and tear stuck in the closed position.

喷油器不供油或压力不足、雾化不良、滴油等；柱塞调节臂或齿杆凸耳从调速杠杆叉槽中脱出处于不供油位置；喷油泵柱塞偶件严重磨损，供油压力太低，出油阀磨损严重，密封不严；垫圈开裂变形，出油阀弹簧折断，喷油器磨损卡死在关闭位置。

Fork Lift, Valve,Body Coupling, Bracket.

供应阀门，叉车起重机，耦合器，插座等。

In this paper,the technique plans of the transmission shaft fork of the econom...

本文分析了用全功能数控车床及立式加工中心加工传动轴节叉的工艺方案，比较了两种方案的加工效率、设备投资及运行的日常费用，为设备采购提供技术支持。

You can do some assertiveness training.

你可以进行一些自信训练。

We were well on the path to making a rear-wheel-drive global platform," says Mays."

我们正致力于建立一个后轮驱动的平台，"Mays这样说道。"