查询词典 tic

With raising temperature and prolonging time of aging treatment, the TiC films coarsen gradually into block so that the notch sensitivity vanished from the alloy.

合金的缺口敏感性与薄膜状TiC沿晶界析出有着密切的关系，随着时效温度的提高和时效时间的延长，晶界薄膜状TiC逐渐变为块状，因而缺口敏感得以消除。

Results indicate that TiC-VC particles can be produced by direct metallurgical reaction between ferrotitanium, ferrovanadium and graphite during the laser cladding process.

研究结果表明，通过钛铁、钒铁与石墨之间的反应，可以得到TiC-VC复合碳化物增强相，细小的TiC-VC复合碳化物颗粒弥散分布在Fe基体之中，合金熔覆层的耐磨性在一定范围内随增强颗粒的增加而提高。

Interlacing interfaces existed between NiAl and TiC may contribute to the enhancement of strength of the NiAl-TiC composites.

在NiAl与TiC之间存在着一种相互交错的界面，它对提高复合材料的高温拉伸强度具有重要贡献。

On the basis of the above, the reactive kinetics has been theoretically analyzed on the diffusion mechanism, and a intrinsic reaction synthesis TiC〓 rate equation has been obtained.

在此基础上，采用扩散机制对TiC〓反应生成动力学进行了理论分析，获得了反应生成TiC〓的动力学特征方程。

Therelationship between solution rate of Al/TiC alloy in rotating Zn melting and thetemperature of Zn melting, rotating rate of axis and uniformization time wascalculated.

分析了各工艺参数对Al／TiC预制合金在锌液中溶解速度的影响，建立了Al／TiC合金在锌液中的溶解率与各参数间的关系式。

Aluminothermic reactive synthesis of Al2O3-TiC nanocomposite powders from a mixture of TiO2, Al, and C powders induced by high-energy ball milling and its consolidation through spark plasma sintering were investigated.

以TiO2、Al、C为原料，首先采用高能球磨引导铝热反应合成了Al2O3-TiC 纳米复合粉体，然后采用放电等离子体烧结纳米复合粉体制备了Al2O3-TiC复合材料。

TiC has a refinement to both primary and eutectic borides, some of which can act as the substrate for primary boride making refinement, the remainder inserting into the primary boride imped it growing in matrix; TiC inserting into the primary boride impedes the eutectic boride growing on the primary boride and decreases the formation of large block eutectic boride.

TiC对初生硼化物和共晶硼化物均有细化作用：一部分作为初生硼化物异质形核核心使其细化，另一部分在基体中嵌入初生硼化物阻碍其生长；嵌入初生硼化物的TiC改变了共晶硼化物依附初生硼化物的特点，使共晶硼化物分布细小均匀。

The results show that the dissolution process of prefabricating alloy can be divided into two periods when the temperature of zinc melt is below the melting point of aluminum.Firstly,zinc melts infiltrates into the prefabricating alloy and then Zn-Al-TiC alloy forms in the surface layer of the prefabricating alloy.Secondly,the Zn-Al-TiC alloy of this alloy surface layer begins to dissolve to the zinc melt.

结果表明：当锌熔体温度低于铝熔点时，预制合金的溶解可分为两个阶段：第一阶段为液态锌向预制合金中浸渗，并在预制合金表层内形成Zn-Al-TiC合金；第二阶段为预制合金表层内的Zn-Al-TiC合金开始溶解并进入锌熔体。

Slag viscosity has been tested by viscometer, slag mineral structure has been observed by microscope of high magnification. First discover that UPC is favorable to weeping and taking shape of high titanium-bearing slag, put forward that the mechanism of titanium slag adhering coke is that TiC、TiN and the carbon of coke which is regard as C〓、C〓、 C〓 shape et al weld into chemical bonding compound.

首次发现UPC有利于高钛渣的形成和滴落，提出了钛渣润湿焦炭的机理是碳以C〓、C〓、C〓等形式与TiC、TiN结合成了强力键化合物及固熔体，粘附在焦炭表面的TiC、TiN层随焦炭下降至风口区被再次氧化，而不会大量弥散于渣中影响其粘度。

The results show that the SHS grain refiners consist of TiC and α-, and that the size and distribution of TiC particles have si...

结果表明：合成的细化剂由TiC和α两相组成，TiC粒子的尺寸和分布对细化剂的晶粒细化效果有显著影响。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。